background image

                                          FMUSER INTERNATIONAL GROUP INC.         

广州市汉婷生物技术开发有限公司

 

 

12

 / 

36

 

 

3.2.2.2 Reference Clock Select   

After  entering  the  submenu  by  pressing  ENTER key, user  can  choose  from  which  the “Reference 

Clock” comes.   

2.2   REF Clock Sel
                 internal    

2.2   REF Clock Sel                                                 

1/1

              [    internal   ]           external             auto   

 

Internal: 

This modulator uses internal 10MHz crystal oscillator as reference clock. 

External: 

This modulator uses external 10 MHz input as reference clock. 

Auto: 

The  modulator  will  preferably  select  the  external  10MHz  input  if  it  exists.  Otherwise  the 

modulator will select the internal 10MHz crystal oscillator’s output as reference clock. 

3.2.2.3 Input select   

2.3   Input Select
                 ASI  1    

2.3   Input Select                                                      

1/1

     [   ASI 1  ]        ASI 2      ASI 3 

ASI 4       IP IN

 

After  entering  the  submenu  by  pressing  ENTER  key,  user  can  choose  the  channel  the  input  TS 

comes from.   

ASI1/2/3/4:

 The input TS comes from port ASI1or 2 or 3 or 4. 

 

IP IN: 

The input signal comes from data port.   

3.2.2.4 IP Input Set 

2.4.1 IP Address                       2.4.2 Port Set

2.4.1 IP Address

224.002.002.002

2.4.2 Port Set

01001

 

Users can modify the IP Address and Port number after entering 2.4 IP Input Set.

 

Summary of Contents for FUTV4502D





































Reviews: