background image

www.fmiproducts.com

116236-01M

29

OpERATING OpTIONAL  

GWMT1 - WALL MOUNTED 

THERMOSTAT

  WARNING:  Do  not  con-

nect the thermostat to a power 

source. Electrical shock and/or 

a fire hazard will occur.

Light  fireplace  as  instructed  in 

Lighting  In-

structions

 on page 27. Set wall thermostat to 

desired temperature.
This thermostat has been electronically cali

-

brated at the factory and requires no adjust

-

ment or leveling.
Upon installation, thermostat must be allowed 
to  stabilize  at  room  temperature  for  a  mini

-

mum of 30 minutes for proper operation.
To turn fireplace off, adjust thermostat to the 
lowest setting and turn gas control knob back 
to PILOT. The pilot will remain lit.

IMPORTANT:

 To turn pilot off, turn gas control 

knob on heater to the OFF position.

OPERATION

Continued

Check  pilot  flame  pattern  and  burner flame 
patterns often.

pILOT ASSEMBLY

The  pilot  assembly  is  factory  preset  for  the 
proper  flame  height. Alterations  may  have 
occurred during shipping and handling. Call 
a qualified service person to readjust the pilot 
if necessary.
The height of thermopile must be 3/8" to 1/2" 
above pilot flame as shown in Figure 46. The 
thermocouple  must  be  at  a  height  of  about 
1/8" above pilot flame. Flame from pilot burner 
must extend beyond both thermocouple and 
thermopile.
If  you  pilot  assembly  does  not  meet  these 
requirements:
•  turn fireplace off (see 

To Turn Off Gas to 

Appliance

, page 28)

•  see 

Troubleshooting

, page 32

Thermocouple

Thermopile

1/8"

Pilot Burner

Piezo Ignitor

Figure 46 - Pilot Assembly

3/8" to 1/2"

OpERATING OpTIONAL 

BLOWER ACCESSORY

Locate  blower  controls  by  opening  lower 
louver panel on fireplace. Blower controls are 
located on the right side of switch bracket to 
the left just inside louver panel.
The BK manual blower and BKT thermostati

-

cally-controlled  blower  have  an  ON  setting 
and an OFF setting. Blower will only run when 
switch is in the ON position. In the OFF posi

-

tion, blower will not operate.

Note  for  BKT  Only:

  If  you  are  using  BKT 

blower with optional thermostat (wall mounted 
or remote control) for fireplace, your fireplace 
and blower will not turn on and off at the same 
time. Fireplace may run for several minutes 
before blower turns on. After heater modulates 
to the pilot position, blower will continue to run. 
Blower will shut off after firebox temperature 
decreases.
The blower helps distribute heated air from the 
fireplace. Periodically check louvers of firebox 
and remove any dust, dirt or other obstruc

-

tions that will hinder the flow of air.

INSPECTING bURNERS

Summary of Contents for VVC42N













































Reviews: