FMI Vantage Hearth VUL24ND Owner'S Operation And Installation Manual Download

Page: 26 / 36

www.fmiproducts.com

123220-01F

TROUbLESHOOTING

WARNING: Turn off heater and let cool before servicing. Only a

qualified service person should service and repair heater.

CAUTION: Never use a wire, needle or similar object to clean

ODS/pilot. This can damage ODS/pilot unit.

Note: All troubleshooting items are listed in order of operation.

POSSIBLE CAUSE

1. Ignitor electrode not con-

nected to ignitor cable

2. Ignitor cable pinched or

wet

3. Broken ignitor cable
4. Bad ignitor
5. Ignitor electrode positioned

wrong

6. Ignitor electrode broken

7. Battery not installed, battery

power low or battery not
installed correctly

1. Gas supply turned off or

equipment shutoff valve
closed

2. Control knob not in PILOT

position

3. Control knob not pressed in

while in PILOT position

4. Air in gas lines when in-

stalled

5. Depleted gas supply (pro-

pane/LP only)

6. ODS/pilot is clogged

7. Gas regulator setting is not

correct

REMEDY

1. Reconnect ignitor cable

2. Free ignitor cable if pinched

by any metal or tubing.
Keep ignitor cable dry

3. Replace ignitor cable
4. Replace ignitor
5. Replace pilot assembly

6. Replace pilot assembly
7. Install new alkaline battery

in electronic ignitor. Verify
battery is installed cor-
rectly

1. Turn on gas supply or open

equipment shutoff valve

2. Turn control knob to PILOT

position

3. Press in control knob while

in PILOT position

4. Continue holding down

control knob. Repeat ignit-
ing operation until air is
removed

5. Contact local propane/LP

gas company

6. Clean ODS/pilot (see

Cleaning and Maintenance

page 25) or replace ODS/
pilot assembly

7. Replace gas regulator

OBSERVED PROBLEM

When ignitor button is

pressed, there is no spark

at ODS/pilot

When ignitor button is

pressed, there is spark at

ODS/pilot but no ignition

Summary of Contents for Vantage Hearth VUL24ND





































Search results

Summary of Contents for Vantage Hearth VUL24ND

Reviews:

Related manuals for Vantage Hearth VUL24ND

Brands by name

Popular brands

FMI Vantage Hearth VUL24ND, Owner'S Operation And Installation Manual

Search results

Summary of Contents for Vantage Hearth VUL24ND

Reviews:

Related manuals for Vantage Hearth VUL24ND

Brands by name

Popular brands