background image

www.fmiproducts.com

123220-01F

20

OPERATION

Continued

7.  With control knob pressed in, press and 

release ignitor button. This will light pilot. 
The pilot is attached to the front burner. 

If needed, keep ignitor button pressed in 

until pilot lights.

 

Note: If pilot does not stay lit, contact a 
qualified service person or gas supplier 
for repairs. Until repairs are made, light 
pilot with match. To light pilot with match, 
see Manual Lighting Procedure.

 

8.  Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds, 

release control knob.

• If control knob does not pop out when 

released,  contact  a  qualified  service 

person or gas supplier for repairs.

 

Note:  If  pilot  goes  out,  repeat  steps  4 
through 8.

9.  Slightly push in and turn control knob 

counterclockwise 

  to  the  ON 

position.

10. Wait  one  minute  and  switch  selector 

switch to the ON position to light burners 
(see Figure 25). When using in the ON 
position  (without  remote)  burners  will 
light on high. There is no adjustment to 

the flames without using remote.

11. To leave pilot lit and shut off burners only, 

turn control knob clockwise 

 to the 

PILOT  position,  or  use  remote  control 
manual OFF button, or set selector switch 

in the OFF position.

  WARNING:  Make  sure  the 

selector  switch  is  in  the  OFF 

position when you are away from 

home for long periods of time. 

Heater  will  come  on  automati-

cally with selector switch in the 

ON position.

ON   REMOTE   OFF

PRG

Figure 25 - Remote Selector Switch in 

ON Position

TO TURN OFF GAS 

TO APPLIANCE

1.  Turn control knob clockwise 

 to the 

OFF position.

2.  Set selector switch in the OFF position.
3.  Close equipment shutoff valve (see Figure 

15, page 16).

MANUAL LIGHTING 

PROCEDURE

1.  Follow steps 1 through 6 under 

Lighting 

Instructions

, page 19.

2.  Depress control knob and light pilot with 

match. 

3.  Keep control knob pressed in for 30 sec-

onds after lighting pilot. After 30 seconds, 

release control knob. Now follow steps 9 
through 11 under 

Lighting Instructions

.

Figure 27 - Pilot 

(Propane/LP)

Pilot 
Burner

Figure 26 - Pilot 

(Natural)

Pilot 
Burner

Ignitor 
Electrode

Ignitor 
Electrode

Summary of Contents for Vantage Hearth VUL24ND





































Reviews: