background image

www.fmiproducts.com

116226-01N

36

SPECIFICATIONS

KC36N, VKC36N, KCC36N and VKCC36N

•  Rating: 23,000/33,000 Btu/hr
•  Gas Type: Natural Gas Only
•  Ignition: Piezo
•  Manifold Pressure: 3.5" w.c.
•  Minimum Inlet Supply Pressure: 5.5" w.c.
•  Firebox Dimensions (HxWxD) (Flanges and 

Standoffs Not Included in Measurement): 

36" x 41" x 21 

1

/

8

" (91 x 104 x 54 cm)

KC36P, VKC36P, KCC36P and VKCC36P

•  Rating: 22,000/31,000 Btu/hr
•  Gas Type: Propane/LP Gas Only
•  Ignition: Piezo
•  Manifold Pressure: 10" w.c.
•  Minimum Inlet Supply Pressure: 11" w.c.
•  Firebox Dimensions (HxWxD) (Flanges and 

Standoffs Not Included in Measurement): 

36" x 41" x 21 

1

/

8

" (91 x 104 x 54 cm)

KC36N-HA, VKC36N-HA, KCC36N-HA 

and VKCC36N-HA

•  Rating: 23,400/33,000 Btu/hr
•  Gas Type: Natural Gas Only
•  Ignition: Piezo
•  Manifold Pressure: 3.8" w.c.
•  Minimum Inlet Supply Pressure: 5.5" w.c.
•  Firebox Dimensions (HxWxD) (Flanges and 

Standoffs Not Included in Measurement): 

36" x 41" x 21 

1

/

8

" (91 x 104 x 54 cm)

REPLACEMENT PARTS

Note: Use only original replacement parts. 

This will protect your warranty coverage for 

parts replaced under warranty.

Contact authorized dealers of this product. If they 

can’t supply original replacement part(s), call FMI 

PRODUCTS, LLC at 1-866-328-4537.
When calling, have ready:

•  your name
•  your address
•  model and serial numbers of your heater
•  how heater was malfunctioning
•  purchase date
Usually, we will ask you to return the part to 

the factory.

SERVICE HINTS

When Gas Pressure Is Too Low

•  pilot will not stay lit
•  burners will have delayed ignition
•  fireplace will not produce specified heat
•  propane/LP gas supply might be low (pro

-

pane/LP units only)

You may feel your gas pressure is too low. If 

so, contact your local gas supplier.

TECHNICAL SERVICE

You may have further questions about installa

-

tion, operation, or troubleshooting. If so, contact 

FMI  PRODUCTS,  LLC  at  1-866-328-4537. 

When calling please have your model and serial 

numbers of your heater ready.
You can also visit web site at

 

www.fmiproducts.com

.

Summary of Contents for (V)KC36N series













































Reviews: