background image

                                    INSTRUCTION MANUAL

 

-3- 

1.

 

Introduction 

The MAXBEC2D is a linear voltage regulator, to provide power for the receiver and servos used in 
your models. For increased safety and reliability of this device, a magnetic switch is used to switch 
the unit on and off. The MAXBEC2D is  fully compatible with  the JETI  DUPLEX System  and can 
also be operated using the JETIBOX terminal. 

To  provide  power  to  the  MAXBEC2D,  a  2-cell  LiPo/LiIon  battery  can  be  used  or  a  5  to  6-cell 
NiMh/NiCd  battery  pack.  The  voltage  regulator  supplies  a  constant  voltage  to  your  receiver  and 
servos, providing smooth servo motion  regardless  of the discharge state  of batteries.  For maximum 
reliability, two battery packs can be used to provide power and the MAXBEC2D features two LED's, 
indicating the connection state of the the connected packs. 

The MAXBEC2D can be monitored and configured via the JETIBOX, either by direct connection, or 
wirelessly  using  the  JETI  DUPLEX  system.  This  allows  the  input  voltage,  temperature  and  output 
voltage to be monitored but also, the output voltage can be configured and alarms can be set for input 
voltage and temperature as required. 

 The system uses the 2.4GHz band to communicate, which allows not only data transmission, but also 
the receiving of data back from the system. During operation, telemetry data allows the condition of 
the system and any measured values to be displayed on the JETIBOX. Switching the MAXBEC2D 
on and off is performed via the special magnetic switch and key, which simply needs to make contact 
with the face-plate in the correct orientation for a short period of time to switch the unit on or off. 

Summary of Contents for MAXBEC2D EX













Reviews: