background image

Removing, Emptying and Refitting the Grassbox

Grassbox Full Indicator
• IMPORTANT

The machine must be switched on for the
grassbox full indicator to operate

1. When the ball reaches the top of the indicator

window, it is time to empty the grassbox. 

See fig-

ure M.

2. When the ball is 

NOT

visible in the indicator win-

dow, grass is being collected. 

See figure M

.

Emptying the Grassbox
• Stop the law n m ow e r, as described in ‘ To Stop yo u r

L aw n m ow e r ’ and wait until the blade has stopped
ro t a t i n g , B E F O R E lifting the grassbox lid.

1. Lift the grassbox lid and rest against the handles 

( N )

.

2. Remove the grassbox using the moulded handle

recesses as illustrated.

(See Figure P)

.

3. Empty grassbox.
4 Replace grassbox and lid carefully.

Failure to fit the grassbox and grassbox lid cor-
r e c t ly will cause poor collection of grass cl i p p i n g s .

M

N

P

grassbox is full

grassbox is

empty

Caring for your Lawnmower

Cleaning 
IMPORTANT:

It is very important that you keep

your lawnmower clean.  Grass clippings left in any
of the air intakes or under the hood could become
a potential fire hazard.  

USE GLOVES

It is recommended that you clean your law n m ow e r
straight after mowing while the grass is still wet.

1. Remove grass from under the hood with the

spanner/scraper tool.

(Q1)

2. Remove the blade, 

see Figure L

, to gain access

to the fan and clean with a soft brush. 

(Q2)

3. Lever the roller out of position and clean with a

soft brush. 

(Q3)

4. Remove grass clippings from:

all air intakes 

(R)

grassbox 

(S)

both sides of grassbox full indicator

(T)

5. Wipe over the surface of your lawnmower with a

dry cloth.

(V)

• IMPORTANT

Never use water for cleaning your lawnmower.
Do not clean with chemicals,  including petrol, or
solvents - some can destroy critical plastic parts.

Transporting the lawnmower.

The lawnmower may be transported on its roller 

( W ) .

At the End of the Mowing Season

1. Replace blade, bolts, nuts or screws, if necessary.
2. Clean your lawnmower thoroughly.
3. Ask your local Service Centre to clean the air filter thor-

oughly and carry out any service or repairs required.

4. Make sure that the electric cable is coiled properly.

Storing the lawnmower 

The handles can be folded to take up the minimum
of space

(X)

• Loosen the handle knobs
• Fold the upper handle over the lawnmower.
• Ensure the switchbox cable is not trapped. 
• Store in a dry place where your lawnmower is

protected from damage.

Q

V

W

X

R

S

1

2

3

T

Summary of Contents for TURBO COMPACT 330









Reviews: