SAFETy PRECAUTIONS
9. Switch off before pushing the product over
surfaces other than grass.
10. Never operate the product with damaged guards
or without guards in place.
11. Switch on the motor according to instructions and
with feet well away from the blade(s).
12. Do not put hands or feet near or under rotating
parts.
13. Do not tilt product when the motor is running,
except when starting and stopping. In this case,
do not tilt more than absolutely necessary and lift
only the part which is away from the operator.
Always ensure that both hands are in the operating
position before returning the appliance to the ground.
14. Never pick up or carry a product when it is
operating or still connected to the mains supply.
15. Remove the plug from the mains :
- before touching the blade (ensure the blade has
come to a complete stop);
-
before leaving the product unattended for any period;
-
before clearing a blockage;
-
before checking, cleaning or working on the appliance;
-
if you hit an object. Do not use your product until
you are sure that the entire product is in a safe
operating condition.;
-
if the product starts to vibrate abnormally. Check
immediately. Excessive vibration can cause injury.
Maintenance and storage
1. Caution: Do not touch rotating blade(s)
2. Keep all nuts, bolts and screws tight to be sure the
product is in safe working condition.
3. Replace worn or damaged parts for safety.
4. Only use the replacement spare parts and
accessories specified for your product.
5. Be careful during adjustment of the product to
prevent entrapment of the fingers between moving
cutting parts and fixed parts of the machine.
6. Renew your metal blade after 50 hours mowing or 2
years whichever is the sooner - regardless of condition.
7. If, during the life of the product, the belt begins to
slip, return the product to an Authorised Service
Dealer for maintenance.
8. Store in a cool dry place and out of reach of
children. Do not store outdoors.
9. Allow the product to cool for atleast 30 minutes
before storing.
SERVICE RECOMMENDATIONS
• your product is uniquely identified by a silver and black product rating label.
• We strongly recommend that your product is serviced at least every twelve months, more often in a professional
application.
GUARANTEE AND GUARANTEE POLICy
If any part is found to be defective due to faulty
manufacture within the guarantee period, Husqvarna UK
Ltd., through its Authorised Service Repairers will effect
the repair or replacement to the customer free of charge
providing:
(a)The fault is reported directly to the Authorised Repairer.
(b)Proof of purchase is provided.
(c)The fault is not caused by misuse, neglect or faulty
adjustment by the user.
(d)The failure has not occurred through fair wear and tear.
(e)The machine has not been serviced or repaired,
taken apart or tampered with by any person not
authorised by Husqvarna UK Ltd..
(f)The machine has not been used for hire.
(g)The machine is owned by the original purchaser.
(h)The machine has not been used outside of the
country for which it was specified.
(i) The machine has not been used commercially.
*
This guarantee is additional to, and in no way
diminishes the customers statutory rights.
Failures due to the following are not covered, therefore it
is important that you read the instructions contained in
this Operator
'
s Manual and understand how to operate
and maintain your machine:
Failures not covered by guarantee
*
Replacing worn or damaged blades
*
Failures as a result of not reporting an initial fault.
*
Failures as a result of sudden impact.
*
Failures as a result of not using the product in
accordance with the instructions and
recommendations contained in this Operator
'
s Manual.
*
Machines used for hire are not covered by this guarantee.
*
The following items listed are considered as wearing
parts and their life is dependent on regular
maintenance and are, therefore not normally subject to
a valid warranty claim: Blades, Electric Mains cable.
*
Caution!
Husqvarna UK Ltd. does not accept liability
under the warranty for defects caused in whole or part,
directly or indirectly by the fitting of replacement parts
or additional parts that are not either manufactured or
approved by Husqvarna UK Ltd., or by the machine
having been modified in any way.
ENVIRONMENTAL INFORMATION
Husqvarna UK Ltd. products are manufactured under an
Environmental Management System (ISO 14001) using,
where practical, components manufactured in the most
environmentally responsible manner, according to
company procedures, and with the potential for recycling
at the end of the products’ life.
• Packaging is recyclable and plastic components have
been labelled (where practical) for categorised
recycling.
• Awareness of the environment must be considered
when disposing of
‘
end-of-life’ product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed
information about recycling of this product, please contact
your local council office, your household waste disposal
service or the shop where you purchased the product.
ENGLISH - 2
To ensure you have a secure connection between the
lawnmower and the extension cable we strongly recommend
you use the following method of attaching the cable:
1. Plug the short connection lead into the socket of the
extension cable.
(M1)
.
2. Form a loop in the end of the extension cable near to
the socket and secure this in the strain relief feature
at the top of the switchbox.
(M2)
This will cause the
socket to hang in a downward direction.
(M3)
CH
