manualshive.com logo in svg

Fluke Hart Scientific 1575 Super-Thermometer, User Manual

Share
Download
Fluke Hart Scientific 1575 Super-Thermometer User Manual Download Page 129

Channel Indicator

The channel indicator is shows which of the scanner channels, if any, is se-
lected for measurement.

Control input (rear panel)

The control input is located on the rear panel of the scanner. The control cable
provided with the scanner connects the control input of the scanner to the con-
trol output of 1575. The control interface provides the control signals and the
power necessary to operate the scanner. The scanner will not operate without
being properly connected to the 1575.

10.5

Scanner Operation

This section explains operation of the 1575 Thermometer with the 2575 Scan-
ner using the front panel buttons and soft-keys.

10.5.1

Soft-key Menus

Besides the display brightness and contrast controls, all instrument functions
are controlled using the soft-key menu system. This menu system is outlined in
the diagram below. In each sub-menu the RETURN soft-key (not shown below)
returns to the next higher menu.

10.5.2

Channel Menu

When the scanner is used with the 1575 Thermometer, the CHANNEL menu of
the 1575 includes additional functions for selecting or automatically sequenc-
ing the channels on the scanner. These functions are SCANNER CHANNEL
and SCANNER SEQ. These soft-keys appear only when the control cable is

119

10 2575 Scanner (optional)

Scanner Operation

Summary of Contents for Hart Scientific 1575 Super-Thermometer





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands