Fluke 80i-110s Instructions Manual Download Page 8

Battery

Type ......................................... 9 volt, IEC 6LR61
Consumption ............................ 8.6 mA typical

12 mA maximum

Service life with Alkaline IEC 6LR61 battery

Typical.............................. 55 hours 
Minimum........................... 40 hours

Battery indicator (ON)............... Green LED dims when battery 

voltage is <6.5 V

Safety

General..................................... IEC 61010-1: Pollution Degree 2
Measurement ........................... IEC 61010-2-032: CAT III 600 V

Electromagnetic Compatibility (EMC)

International.............................. IEC 61326-1: Portable 

Electromagnetic Environment
CISPR 11: Group 1, Class A 

Group 1: Equipment has intentionally generated and/or use 
conductively coupled radio-frequency energy which is necessary for 
the internal functioning of the equipment itself. 
Class A: Equipment is suitable for use in all establishments other 
than domestic and those directly connected to a low voltage power 
supply network which supplies buildings used for domestic purposes. 
There may be potential difficulties in ensuring electromagnetic 
compatibility in other environments, due to conducted and radiated 
disturbances. 
Caution: This equipment is not intended for use in residential 
environments and may not provide adequate protection to radio 
reception in such environments.
Emissions that exceed the levels required by CISPR 11 can occur 
when the equipment is connected to a test object.

USA (FCC) ............................... 47 CFR 15 subpart B. This product is 

considered an exempt device per 
clause 15.103.

Electrical Specifications 

Valid temperature ............................. 23 °C ±3 °C (73 °F ±5 °F).
Current Ranges ................................ 0 A dc to 10 A dc or ac peak

0 A dc to 100 A dc or ac peak

Output Signals.................................. 10 A range: 100 mV/A

100 A range: 10 mV/A

Basic Accuracy (DC to 1kHz):

Input Current 

(DC or AC peak)

Error (after zero check)

Range 100 mV/A 

Range 10 mV/A

0 A to 10 A
0 A to 40 A
40 A to 80 A
80 A to 100 A

<3 % of r50 mA

-
-
-

-

<4 % of r50 mA
<12 % of r50 mA
<15 % of reading

80i-110s.book  Page 8  Monday, December 5, 2016  12:12 PM

Summary of Contents for 80i-110s













Reviews: