Fluke 80i-110s Instructions Manual Download Page 12

LIMITED WARRANTY AND LIMITATION OF LIABILITY

This Fluke product will be free from defects in material and workmanship 

for one year from the date of purchase. This warranty does not cover 

fuses, disposable batteries, or damage from accident, neglect, misuse, 

alteration, contamination, or abnormal conditions of operation or handling. 

Resellers are not authorized to extend any other warranty on Fluke’s 

behalf. To obtain service during the warranty period, contact your nearest 

Fluke authorized service center to obtain return authorization information, 

then send the product to that Service Center with a description of the 

problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, 
SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED 
OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, 
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING 
FROM ANY CAUSE OR THEORY. Since some states or countries do not 
allow the exclusion or limitation of an implied warranty or of incidental or 
consequential damages, this limitation of liability may not apply to you.

11/99

Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.

Fluke  Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands

80i-110s.book  Page 12  Monday, December 5, 2016  12:12 PM

Summary of Contents for 80i-110s













Reviews: