background image

 

Specifications  

Operating Temperature ................... -20 

°

C to +50 

°

C  

Storage Temperature ...................... -20 

°

C to +70 

°

Operating Humidity.......................... 5 % to 95 % relative humidity, non-condensing 
Operating Altitude............................ <2000 m 
Pressure Range .............................. 0 MPa to 21 MPa (3000 psi) 

Adjustment Resolution .................... 0.05  % of reading  

Wetted Materials  

(700HPP) ..............................  Acetal, Aluminum, Brass, Silicone Loctite 577, Nitrile, Polypropylene, PTFE, Steel, 

Stainless Steel, Viton 

(700HPM) ............................. Aluminum, Stainless Steel, Nitrile, Urethane, PVC 

Leak Rate (700HPPK,  
with isolation valve closed) .............. 0.01  % reading  
Weight ............................................. 7257  g (16.0 lb) 

Dimensions ..................................... 740  x  295 x 155 mm  

 

(29.13 x 11.61 x 6.10 in) 

Safety: 

General ...................................... IEC 61010-1 

 

LIMITED WARRANTY AND LIMITATION OF LIABILITY 

This Fluke product will be free from defects in material and workmanship for one year from the date of purchase. This warranty 

does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal 

conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To obtain 

service during the warranty period, contact your nearest Fluke authorized service center to obtain return authorization 
information, then send the product to that Service Center with a description of the problem. 
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR 

PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR 

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do 

not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of liability 

may not apply to you. 
 

Fluke Corporation 

P.O. Box 9090 

Everett, WA 98206-9090 

U.S.A. 

Fluke Europe B.V. 

P.O. Box 1186 

5602 BD Eindhoven 

The Netherlands 

11/99 

 

Summary of Contents for 700HPPK







Reviews: