background image

 

 0.1- 1  second …………………… 0.1 -------------------------------------------------------------------1 second 
 1  -  10 seconds …………………  1 --------------------------------------------------------------------10 

seconds 

 6  -  60 seconds …………………  6 -------------------------------------------------------------------- 60 

seconds 

 1  -  10 minutes …………………   1 -------------------------------------------------------------------- 10 

minutes 

 6  -  60 minutes …………………   6 -------------------------------------------------------------------- 60 

minutes 

 1 -  10 h …………………………..   1 -------------------------------------------------------------------- 10 hours 
 10 - 100 h ………………………… 10 ------------------------------------------------------------------- 100 hours 

 NOTE : On 6-60 time range multiply the time set scale by 6. 

  Example – On-delay of 18 seconds is required. 

a.

Set the time range knob to 6-60s position.

b.

Set the time set knob to 3. (3x6 = 18 seconds.)

3.

State indicator Un signals.

a.

No light

 = The timer is in off state. (No supply on A1/A2 terminals)

b.

Blinking light

 = The timer is counting/On delay.

c.

Steady light

 = The timer  reached the time set. (Internal relay energized)

For more information:

WEB: FLTR.com.au   PHONE: (+61) 1300 62 4020   EMAIL: [email protected]   SKYPE: Purple.Engineering

Summary of Contents for CSB 10























Reviews: