background image

5

flowserve.com

Serck Audco TIPV Twin Isolation Plug Valve FCD - SRENIM0005-05 A4 – 02/17

       

Each valve has one of the following identification information plates attached to the body.

 

     

 

 

   

 

 

 

         

2.1   

Pressure Equipment Directive: If the identity plate carries the Notified Body identity number ‘0086’ beside

     

the ‘CE’ mark, the product complies with the Pressure Equipment Directive 2014/68/EU and the Pressure  

Equipment Regulations 1999 (SI 1999/2001). Without these numbers, and when used within the European 

community, the product is classified as ‘SEP’ (Sound Engineering Practice and may only be used within the 

limitations defined in tables 6, 7, 8 & 9 of Schedule 3 of the Pressure Equipment Regulations.

2.2     

ATEX Directive: If the identity plate carries the Explosion Protection Symbol and codes identifying the 

       

equipment group and category, the zone suitability and protection type beside the CE mark, the product 

       

complies with the ATEX Directive and The Equipment and Protective Systems for Use in Potentially   

 

 

 

 

 Explosive 

Atmospheres 

Regulations 

1996. 

        

 

 

 

 Definition 

of 

identity 

plate 

marking 

above: 

        

       

‘II’ = Equipment Group; ‘2’ = Equipment Category; ‘G’ = Gas Zone suitability (Zones 1 & 2);  

 

 

       

‘D’ = Dust Zone suitability (Zones 21 & 22); ‘c’ = type of protection i.e. constructional safety  

 

 

 

 

 

 (BS 

EN 

13463-5). 

      

       

‘X’ = Special temperature reference.

2.3     

Material traceability markings are hard marked on the body and cover.




































































































°


















2       

VALVE MARKINGS

Summary of Contents for Serck Audco





















Reviews: