manualshive.com logo in svg

Flowserve Argus EK 71, Service Manual

Share
Download
Flowserve Argus EK 71 Service Manual Download Page 15

Argus 

Maintenance 

15 

Type FK/79 

 

 
 

FK79-02-001 

 

 

 

Danger! 

Do not disassemble the valve under pressure. Before disassembly operate valve so that possible 
pressure behind the ball may escape. 

Disassembly 

f

  Stem (22) should be in CLOSED position.  

f

  Remove snap ring (12) and stop ring (7). Unscrew cheese-head screws (8). 

f

  Take off plate (6) with sealing ring (43) and bush (36) on DN 20 and 25 or bearing tape (34) and dowel 

pin on DN 32-50 as well as thrust ring (11) with sealing ring (35). 

∗∗

 

f

  Unscrew hexagonal nuts (4) from body (2). 

f

  Take off body (2), O-ring (37) and sealing ring (33) from body (1). 

f

  Remove ball (21) and sealing rings (31). 

f

  Press stem (22) downwards and take it out of the body together with bush (36) and washer (38). 

f

  Removed O-ring (32) and washer (39) upwards. 

Exchanging the Stem Sealing 

Proceed as per Disassembly until 

(∗∗)

. 

f

  Take off O-ring (32) and exchange bearing ring (39). 

 

When using a PTFE seal instead of O-ring (32), item (39) can be left out. 

 

Depending on the actual requirements, a partial disassembly of the ball valve might be sufficient. 

f

  To reassemble, proceed in reverse order. 

 

  三千控制阀网 

www.cv3000.com

Summary of Contents for Argus EK 71
























Reviews:

No comments

Brands by name

Popular brands

Load more brands