manualshive.com logo in svg

Flowserve Argus EK 71, Service Manual

Share
Download
Flowserve Argus EK 71 Service Manual Download Page 11

Argus 

Maintenance 

11 

Type FK/74 

 
 

FK74-02-001 

 

 

 

Danger! 

Do not disassemble the valve under pressure. Before disassembly operate valve so that possible 
pressure behind the ball may escape. 

Disassembly 

f

  Stem (31) should be in CLOSED position. 

f

  Remove thrust ring (22) and stop disk (10). 

f

  Detach hexagon nut (15) with ring (16). 

f

  Remove cover plate (11) with dowel pins (7, 12), bearing tape (55) and sealing ring (42) as well as 

thrust ring (18) with sealing ring (49). 

∗∗

 

f

  Unscrew flange connection (2) with sealing ring (51) and O-ring (52) from body (1) using a special 

ARGUS tool (eccentric). 

f

  Remove ball (30), spring washers (21) and annular piston (50). 

f

  Press stem (31) downwards and take them out of body with thrust ring (44) and bushing (59). 

f

  Remove ring (43), O-ring (47), compression spring (17) as well as rings (45) upwards. 

Exchanging the Stem Sealing 

Proceed as per Disassembly until 

(∗∗)

. 

f

  Remove ring (43), O-ring (47) and replace. 

When using a PTFE seal instead of the O-ring (47), item (43) can be left out. 

Items (45) and (17) will then be replaced by a ring. 

 

Depending on the requirements, a partial disassembly of the ball valve may be sufficient. 

f

  To reassemble, proceed in reverse order. 

  三千控制阀网 

www.cv3000.com

Summary of Contents for Argus EK 71
























Reviews:

No comments

Brands by name

Popular brands

Load more brands