background image

 

 

 
 

 

Flowserve Corporation 

1978 Foreman Drive 

Cookeville, Tennessee, USA,  38501 

931 432-4021 

 

Flowserve Flow Control UK Ltd 

Haywards Heath, West Sussex, Uk 

44 (0)1444 314400 

 

Flowserve Corporation 

12 Tuas Avenue 20 

Singapore 

68798900 

 

Flowserve Corporation 

Rua Tocantins, 128 

São Caetano do Sul, SP, Brazil 

55 11 2169-630

 

 

 
 

 
Representative: 

 

 

To find your local Flowserve representative please 
use the Sales Support Locator System found at 
www.flowserve.com 
 
Or call toll free: 1-931-432-4021 

Bulletin FCD AXENIOM0125-00 

 

Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this 
Flowserve product is designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products 
should be aware that Flowserve products might be used in numerous applications under a wide variety of industrial service conditions. Although 
Flowserve can provide general guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser/user must 
therefore assume the ultimate responsibility for the proper sizing and selection, installation, operation, and maintenance of Flowserve products. 
The purchaser/user should read and understand the (INSERT OFFICIAL USER INSTRUCTION TITLE) instructions included with the product, 
and train its employees and contractors in the safe use of Flowserve products in connection with the specific application.  
 
While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only 
and should not be considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be construed 
as a warranty or guarantee, express or implied, regarding any matter with respect to this product. Because Flowserve is continually improving 
and upgrading its product design, the specifications, dimensions and information contained herein are subject to change without notice. Should 
any question arise concerning these provisions, the purchaser/user should contact Flowserve Corporation at any one of its worldwide operations 
or offices.  
 
For more information about Flowserve Corporation, contact 

www.flowserve.com

 or call USA 1-800-225-6989.

  

 
 

Summary of Contents for APEX 7000












Reviews: