background image

9

 

as the battery charge lasts. You may need to replace the 
battery afterwards.

 

2.

 

If 115VAC power is ON, the charger/controller continues 
to try to charge the battery at a charging rate of .5 AH 
until the battery charge is more than 20%, at which 
point the charger will resume charging at a rate of  2 AH.

 

3.

 

If the pump is running and the AC power is on, you may 
need to stop the pump to allow the battery to charge.

 

Follow the battery manufacturer’s recommendations for 

maintenance and safe use of the battery.

 

1.

 

Connect the 

positive

 (+) charger/controller lead wire 

(red) to the 

positive

 (+) battery terminal (red). Connect 

the 

negative

 (

) charger/controller lead wire (black) to 

the 

negative

 (

) terminal (black) on the battery. If you 

are using two batteries, use the set of optional terminals 
and connect the second battery. Use lead wires (not 
included) to connect the 

positive

 (+) charger/controller 

terminal to the 

positive

 (+) battery terminal and the 

negative

 (

) charger/controller terminal to the 

negative

 

(

) battery terminal.

 

 

2.

 

The backup pump leads are polarity sensitive; connect 
the 

positive pump lead to the terminal labeled Pump ‘+’ 

Wiring 

 Setup 

 

 

Summary of Contents for BDWWHU


















Reviews: