background image

5

Floataway Installation Manual 230v 50Hz Tranquility 2017 - v3

Please read through this Manual before beginning the installation.  If you are not confident 

of success, please hire an electrician to do the installation for you.  Floataway will not be 

responsible for installation errors caused by not using these instructions.

The Heater Insulation Panel

 

The heater insulation is a thick high temperature rigid aluminium 

coated mat.  The tub sits on top of this piece and is positioned 

approximately 8 inches from the back wall in the float room.  

The Silicone Heater membrane sheets

The heaters must sit on top of the silicone sheet membrane, it is 

a white soft foamed rubber sheet 2mm thick. The silicone sheet 

is WHITE and comes rolled up. Lay the silicone sheets down on 
the insulation panel ready for the heaters.

The Heater Panels

The heater panels, smooth metal side facing upwards, are posi-

tioned over the high temperature insulation. The drawing below 

shows both sides of the heater panel. Be sure that the coil sides 

are facing the insulation so that you see the smooth side facing 

you as shown below right.    

   

 

The drawing shows the correct 

position of the heater panels

The heater with a longer wire 

goes at the front of the product.

The cables run back to the con-

trol box on the tank and should 

not be trapped under the tub.

Check that there are no foreign bodies on the top surface of 

the heater, or on the bottom of the tub, before the tub is added.  

Small hard objects may break the bottom of the tub when water 

is added, or cause local hot spots or noises.  

The heaters are not supplied connected to the control box and must be fed through cable ties 

along the tank and then the glands and connected to ground (5), neutral (2), series connection(8)

and switched live (Heater MCB 1) connections in the control box.   (See connection information 

under “control box” section.)  A small portion of the heaters should stick out from under the tub (ap-

proximately an inch) to enable earth bond testing.

The Tub

Place the tub gently onto the insulation and heater panels. The heater panels and insulation may 

be walked on during this manoeuvre. Remove any packaging from the tub and clean it thoroughly, 

first using soapy water, then if necessary  lighter fuel (not acetone) for stubborn marks.  Position 

the tub so that its base sit exactly on top of the insulation.

Summary of Contents for TRANQUILITY







































Reviews: