6
H-Type
®
Precleaner with XF2-Tips
4.1 H-Type® Precleaner with HXF or HXF2 Tips
Section 4 – Installation Instructions
Pole Location Specs
For specific cleaner specs see charts on page 8
A
X
C
A = Pulley Di Lagging and Belt
C = Critical Spec to move location if necessary
Y
Move Dim. C
on arc
½ diameter of
pulley shaft
Belt Direction
“B”
“A”
X
Modified
Intersecting
mark
“B”
Belt Direction
Offset
Bracket
Xf2-Tip
Pole
Pivot Arm
Torque
Arm
HXF2 Parts List
Cushion
Tension
Spring
Mounting Plate
Pole Lock
Collar
(Hidden)
Pivot Shaft
Bracket
Maximum
lump size + 8”
(200mm)
Chute wall
Space needed to avoid clogging chute
Pole Location Specs
For specific cleaner specs see charts on page 8
A
X
C
A = Pulley Di Lagging and Belt
C = Critical Spec to move location if necessary
Y
Move Dim. C
on arc
½ diameter of
pulley shaft
Belt Direction
“B”
“A”
X
Modified
Intersecting
mark
“B”
Belt Direction
Offset
Bracket
Xf2-Tip
Pole
Pivot Arm
Torque
Arm
HXF2 Parts List
Cushion
Tension
Spring
Mounting Plate
Pole Lock
Collar
(Hidden)
Pivot Shaft
Bracket
Maximum
lump size + 8”
(200mm)
Chute wall
Space needed to avoid clogging chute
Pole Location Specs
For specific cleaner specs see charts on page 8
A
X
C
A = Pulley Di Lagging and Belt
C = Critical Spec to move location if necessary
Y
Move Dim. C
on arc
½ diameter of
pulley shaft
Belt Direction
“B”
“A”
X
Modified
Intersecting
mark
“B”
Belt Direction
Offset
Bracket
Xf2-Tip
Pole
Pivot Arm
Torque
Arm
HXF2 Parts List
Cushion
Tension
Spring
Mounting Plate
Pole Lock
Collar
(Hidden)
Pivot Shaft
Bracket
Maximum
lump size + 8”
(200mm)
Chute wall
Space needed to avoid clogging chute
Fig. 1
Pole Location Specs
For specific cleaner specs see charts on page 8
A
X
C
A = Pulley Di Lagging and Belt
C = Critical Spec to move location if necessary
Y
Move Dim. C
on arc
½ diameter of
pulley shaft
Belt Direction
“B”
“A”
X
Modified
Intersecting
mark
“B”
Belt Direction
Offset
Bracket
Xf2-Tip
Pole
Pivot Arm
Torque
Arm
HXF2 Parts List
Cushion
Tension
Spring
Mounting Plate
Pole Lock
Collar
(Hidden)
Pivot Shaft
Bracket
Maximum
lump size + 8”
(200mm)
Chute wall
Space needed to avoid clogging chute
Fig. 2
Physically lock out and tag the conveyor at the power source
before you begin cleaner installation.
Pole Location Specs
For specific cleaner specs see charts on page 8
A
X
C
A = Pulley Di Lagging and Belt
C = Critical Spec to move location if necessary
Y
Move Dim. C
on arc
½ diameter of
pulley shaft
Belt Direction
“B”
“A”
X
Modified
Intersecting
mark
“B”
Belt Direction
Offset
Bracket
Xf2-Tip
Pole
Pivot Arm
Torque
Arm
HXF2 Parts List
Cushion
Tension
Spring
Mounting Plate
Pole Lock
Collar
(Hidden)
Pivot Shaft
Bracket
Maximum
lump size + 8”
(200mm)
Chute wall
Space needed to avoid clogging chute
HXF2
Blade Size
Pulley Diameter
+ Belt and Lagging
SS
250 - 475mm (10" - 19")
S
500 - 775mm (20" - 31")
M
800 - 975mm (32" - 39")
L
1000 - 1175mm (40" - 47")
1. Find X, Y & C measurements. Find the X and Y measurement
specifications for the pulley diameter. See charts on page 8. The pulley
diameter measurement should include lagging and belt.
Pulley Diameter ________"; X=________"; Y=________"; C=________".
Using the correct X and Y coordinates will position the cleaner blades at
15° below the horizontal plane on the head pulley.
2. Measure head pulley shaft.
Determine the diameter of the pulley shaft
and divide by 2. ________"
3. Locate horizontal line from center of pulley shaft.
Put a level on top of
the pulley shaft and draw a horizontal line A. Measure down from Line
A half the diameter of the pulley shaft and draw Line B parallel from the
pulley shaft (Fig. 1).
4. Mark X dimension.
Subtract the above dimension (Step 2) from the
selected X dimension to establish the modified X dimension. With this
new X dimension measure horizontally from the front of the pulley shaft
forward on Line B and mark on the chute (Fig. 2).
Tools Needed:
• Tape measure
• Level
• Wrenches or Crescent Wrenches:
(1) M10 (17mm)
(2) M12 (19mm)
(1) M16 (24mm)
(2) M24 (36mm)
Maximum
lump size
+ 200mm (8")
