background image

www.flexco.com

—4—

Electric Belt Cutter

General Safety Rules  

  

Save These Instructions–

Signal words:

“DANGER” indicates an imminently hazardous 

situation which, if not avoided, will result in 

death or serious injury. The signal word is 

limited to the most extreme situations.
“WARNING” indicates a potentially hazardous 

situation which, if not avoided, could result in 

death or serious injury.
“CAUTION” indicates a potentially hazardous 

situation which, if not avoided, may result in 

minor or moderate injury. It may also be used to 

alert against unsafe practices.

Safety Symbol

!

This international safety symbol is used to 

identify and call attention to specific safety 

matters.

Safety Information

To Avoid Severe Personal Injury or Property 

Damage, read carefully and understand the 

following Safety Precautions.

1. WOrk ArEA

!

CAUTION

Keep your work area clean and well lit. Cluttered 

benches and dark areas invite accidents.

!

dANGeR

Do not operate power tools in explosive 

atmospheres, such as in the presence of 

flammable liquids, gases, or dust. Power tools 

create sparks which may ignite the dust of fumes.

!

CAUTION

Keep bystanders, children, and visitors away 

while operating a power tool. Distractions can 

cause you to lose control.

!

WARNING

Never leave tool until it comes to a complete stop.

!

CAUTION

Operation of gear units is permitted at ambient 

temperatures between -4°F and +104°F (-20°C 

and +40°C).  However, for temperatures between 

-4°F and +14°F (-20°C and -10°C) unit may 

only start up after it has been progressively and 

evenly pre-heated, or otherwise initially operated 

unloaded. Load may then be connected to the 

output shaft when the gear unit has reached the 

temperature of 14°F (-10°C) or higher.

2. ElECTrICAl SAfETy

!

dANGeR

Double Insulated tools are equipped with a 

polarized plug (one blade is wider than the 

other). This plug will fit in a polarized outlet 

only one way. If the plug does not fit fully in 

the outlet, reverse the plug. If it still does not 

fit, contact a qualified electrician to install a 

polarized outlet. Do not change the plug in any 

way. Double Insulation eliminates the need 

for the three wire grounded power cord and 

grounded power supply system.

Summary of Contents for CEBC1













Reviews: