FlameStop VESDA-E VEP-A00-1P Product Manual Download Page 79

Page: 79 / 112

VESDA-E VEP-A00-P Product Guide

www.xtralis.com

Parameter

Default Values

Range

Affected by Return to

Factory Defaults

command

Minimum

Maximum

GPI Function
(Monitored)

Mains OK

n/a

Yes

Relays

Assignment of Relays
to conditions

See Table 4-2

n/a

Yes

Normally Energized

See Table 4-2

n/a

Yes

Latching

Checked

Unchecked

Checked

Yes

Button Lockout

Lockout

Reset

Unchecked

Checked

Yes

Disable

Unchecked

Checked

Yes

AutoLearn Smoke and Flow Commands

Duration

14 days

15 minutes

16 days

n/a

Table 5-4: Default Settings (continued...)

The Xtralis VSC software forces the user to move the detector to a valid zone number.

The user must set the password the first time. There is no default password.

Default value set in factory. Not modified by return to factory defaults command.

The WiFi Security Key type depends on the WiFi security method in use.

Pipes in Use can not be configured for VEP-A00-1P.

Aspirator Speed can not be configured for VEP-A00-1P.

Summary of Contents for VESDA-E VEP-A00-1P

















































































































Search results

Summary of Contents for VESDA-E VEP-A00-1P

Reviews:

Related manuals for VESDA-E VEP-A00-1P

Brands by name

Popular brands

FlameStop VESDA-E VEP-A00-1P, Product Manual

Search results

Summary of Contents for VESDA-E VEP-A00-1P

Reviews:

Related manuals for VESDA-E VEP-A00-1P

Brands by name

Popular brands