background image

STRA-14 Room controller. Installation and maintenance manual.

Fläkt Woods

8710 GB 2016.09.08

1 (12)

Specifications are subject of alteration without further notice.

STRA-14 for chilled beams

STRA-14 is the room controller for the motorised energy control

(MEC) and constant air volume chilled beams

It is possible to set different parameter values in a parameter menu

in the display, using the buttons on the controller. You change

parameter values with the INCREASE and DECREASE buttons and

confirm changes with the Function button.

Technical data

Supply voltage

18...30 V AC, 50...60 Hz

Internal consumption

2.5 VA

Ambient temperature

0...50°C

Storage temperature

-20...+70°C

Ambient humidity

Max 90% RH

Protection class

IP20

Communication

RS485 (EXOline or Modbus) with automatic detection/change-over

Modbus - Bacnet - MSTP

8 bits, 1 or 2 stop bits. Odd, even (FS) or no parity.

Communication speed

9600 bps (not changeable)

Built-in temperature sensor

NTC type, measuring range 0...50°C, ac/-0.5°C at 15...30°C

Material, casing

Polycarbonate, PC

Weight

110 g

This product conforms with the requirements of European EMC standards CENELEC EN 61000-6-1 and EN

61000-6-3, and the requirements of European LVD standard IEC 60 730-1. It carries the CE mark.

Inputs

External room sensor

PT1000-sensor, 0…50°C. Suitable sensor is Fläkt Woods STRZ-05

Occupancy detector

Closing potential-free contact. Suitable occupancy detector is Fläkt Woods STRZ-09.

Condensation detector alt.

window contact

Fläkt Woods condensation detector STRZ-16 alt. window contact STRZ-38 resp.

potential-free contact

CO 

2

 sensor

STRZ-18 (0-10V).

Outputs

Forced ventilation

24 V AC actuator, max 0.5 A

Valve actuator alt. thermal

actuator

2 outputs

Valve actuator

0…10 V DC, max 5 mA

Thermal actuator

24 V AC, max 2.0 A

Control

Heating or cooling

Actuator exercise

FS = 23 hours interval

Terminal blocks

So-called lift type for cable cross-section 2.1 mm2

Summary of Contents for STRA-14













Reviews: