background image

 

40

The exact agreement between the CM and the WM is 86.3% (483/560) with 95% CI: (83.2%; 89%).   
Agreement /- 1 block is 97.7% (547/560) with 95% CI: (96.1%; 98.8%).     

Leukocyte  

Bayer Clinitek 500 Urine Chemistry Analyzer 

 

 

 

15  70  125 500 Total 

268 

23 

4 0 0 295 

15 

14 

34 

17 

0 0 65 

70 

8 10 

53 

7 3 81 

125 

1  0  4  80 22 107 

AimStrip

®

   

Urine 

Analyzer 

500 

0 0 0 1 11 

12 

 

Total 

291 

67 78 88 36 560 

The exact agreement between the CM and the WM is 79.6% (446/560) with 95% CI: (76.0%; 
82.9%).    Agreement /- 1 block is 90.5% (507/560) with 95% CI: (87.8%; 92.8%).   

Protein  

Bayer Clinitek 500 Urine Chemistry Analyzer 

 

 

 

0 15 

30 

100 

300 

Total 

265 10  0  0 

275 

15 

19 42 13 0  0  74 

30 

0 9 48 

17 

0 74 

100 

0 0 0 42 

9 51 

AimStrip

®

   

Urine 

Analyzer

 

300 

0 0 0 0 86 

86 

 

Total 

284 61  61  59  95  560 

The exact agreement between the CM and the WM is 86.3% (483/560) with 95% CI: (83.2%; 89%).   
Agreement /- 1 block is 94.8% (531/560) with 95% CI: (92.7%; 96.5%).     

Ketone  

Bayer Clinitek 500 Urine Chemistry Analyzer 

 

 

 

0 5 15 40 80 Total 

317 10  0 

327 

5 55  9  0  0  69 

15 

0 0 52 21  0  73 

40 

0 0  6  46  2  54 

AimStrip

® 

Urine  

Analyzer 

80 

0 0  0  9  28  37 

 Total 

322 65  67  76  30  560 

The exact agreement between the CM and the WM is 88.9% (498/560) with 95% CI: (86.0%; 
91.4%).    Agreement /- 1 block is 97.3% (545/560) from each other with 95% CI: (95.6%; 
98.5%).  

Summary of Contents for AimStrip



















































Reviews: