background image

 

39

Results of CLIA Waiver Study 

A total of nine untrained non-laboratory users from three clinical sites in the US participated in the 
study by testing a total of 560 urine samples using the

 

AimStrip

®

 

Urine Analyzer and the 

CTMI

 

CT-120 Analyzer over 2 month period.  The 

AimStrip

®

 

Urine Analyzer is intended for use in 

conjunction with the 

AimStrip

®

 and 

Fisherbrand

®

 

Urinalysis Reagent Strips for detection of the 

following analytes in urine: Glucose, Blood, Protein, Leukocyte, Nitrite, Bilirubin, Ketone, pH, 
Specific Gravity, and Urobilinogen. At each study site, approximately 120 clinical urine specimens 
were tested by three untrained, non-laboratory participants: phlebotomist, medical assistants, and 
ultrasound technician. The results (WM) were compared with the same specimens tested by 
professionally trained operators using Bayer’s Clinitek 500 Urine Chemistry Analyzer (CM).     

The CLIA waiver study demonstrated that the following performance data of the 

AimStrip

®

 Urine 

Analyzer in the hands of non-technical users when using only the Quick Reference Guide.     

Bilirubin  

Bayer Clinitek 500 Urine Chemistry Analyzer 

 

 

 

0  1 2 4 

Total 

410 

8 1 0 419 

8  15 

0 0 23 

4  12 21 5  42 

AimStrip

®

 

Urine 

Analyzer 

0  1 1 74 

76 

 

Total 

422

36

23 79

560

The exact agreement between the CM and the WM is 92.9% (520/560) with 95% CI: (90.4%; 
94.8%). Agreement /- 1 block is 96.1% (538/560) with 95% CI: (94.1%; 97.5%).     

Blood  

Bayer Clinitek 500 Urine Chemistry Analyzer

 

 

0

10

25

80

200

Total

191 16  1  0  0 

208 

10 

11 37 4  0  0  52 

25 

0 14 

39 

8 0 61 

80 

0 0 7 35 

0 42 

AimStrip

®

 

Urine 

Analyzer 

200 

0 0 0 13 

184 

197 

 

Total 

202

67

51

56

184

560

The exact agreement between the CM and the WM were 86.8% (486/560) with 95% CI: (83.7%; 
89.5%).    Agreement /- 1 block was 95% (532/560) with 95% CI: (92.9%; 96.7%).     

Glucose  

Bayer Clinitek 500 Urine Chemistry Analyzer

 

 

0

100

250

500

1000

Total

389 

4 0 0 0  393 

100 

4 32 

5 0 0  41 

250 

3  14 45 2  0  64 

500 

0 0 8 9 1  18 

AimStrip

®

 

Urine 

Analyzer 

1000 

0

0

2

34

8

44

 

Total 

396

50

60

45

9

560

Summary of Contents for AimStrip



















































Reviews: