Fisher EZR Instruction Manual Download Page 16

Page: 16 / 40

Type EZR

1 11

Converting a Fisher

E-Body to Type EZR:

Remove all trim parts from the main valve and clean

the body interior. Then follow procedure in Assembly

section to convert a Fisher

E-body to a Type EZR.

cAUTIOn

when installing a Type EZR trim package

make sure flow is up through the center

of the cage and down through the cage

slots. In some cases, correct flow path is

achieved by removing the body from the

line and turning it around. If this is done,

change the flow arrow to indicate the

correct direction. Damage may result if

flow is not in the correct direction. After

assembly, check the regulator for shutoff

and leakage to atmosphere.

Disassembly

Disassembly of Type EZR:

1. Shutdown, isolate, and depressurize the main

valve and pilot.

2. Remove the cap screws (key 3). Lift up and

remove the bonnet (key 2) from the body (key 1).

Note

For the NPS 8 (DN 200) body, the

lifting flange (key 143) is capable

of supporting the full weight of the

regulator assembly and can be utilized

to lift bonnet if required.

3. Remove the diaphragm and plug assembly

(key 9) and bonnet O-ring (key 28). For NPS 2 x 1

(DN 50 x 25) sizes, use a screwdriver to remove

the upper adaptor (key 131).
4. Pull out the cage (key 7), O-ring (key 8),

and inlet strainer or strainer shim (key 23) (if

no strainer). For NPS 2 x 1 (DN 50 x 25) sizes,

remove the lower adaptor (key 132).
5. Clean parts and replace if necessary. To change

the O-ring (key 121) on a 6-inch (152 mm) cage with

attached restrictor plate (key 71), remove cap

screws (key 126).

Assembly

1. Install the inlet strainer or shim (key 23) into the

body (key 1).

Note

when installing in a vertical orientation,

apply lubricant to the bottom of the inlet

strainer or strainer shim (key 23) to help

hold parts in place while installing cage.

2. Lightly lubricate and install the cage O-ring (key 8).
3. Apply lubricant lightly to all O-rings or the mating

part before installing them.

4. Install the cage (key 7) and lightly lubricate and

install the bonnet O-ring (key 28).

To assemble a 6-inch (152 mm) cage with

attached restrictor plate (key 71), lightly lubricate

the O-ring (key 121) and place it on the restrictor

plate. Secure the cage to the restrictor plate with

the cap screws (key 126), using a torque of 10 to

12 foot-pounds (14 to 16 N•m).

STYLE

MATERIAL

DIAPhRAGM MATERIALS

Imprint Ink Mark Imprint Ink Mark

130

17E68

17E68 - Nitrile (NBR)

(low temperature)

17E88

17E88 - Fluorocarbon (FKM)

(high aromatic hydrocarbon

content resistance)

17E97

17E97 - Nitrile (NBR)

(high pressure and/or

erosion resistance)

Table 11.

Diaphragm Imprint Codes

Figure 8.

Diaphragm Markings

LOCATE INK CODE

BETwEEN RADII

MATERIAL

INK CODE

MANUFACTURER

CODE

ThICKNESS INK

CODE(USE ONE

LOcATIOn OnLY)

DOME IDENTIFICATION

ELASTOMER/FABRIC

MATERIAL CODE

ThICKNESS

CODE

YEAR OF MANUFACTURE

RADIAL LOCATION

TO LOcATE

IMPRINT CODE

Summary of Contents for EZR









































Search results

Summary of Contents for EZR

Reviews:

Related manuals for EZR

Brands by name

Popular brands

Fisher EZR, Instruction Manual

Search results

Summary of Contents for EZR

Reviews:

Related manuals for EZR

Brands by name

Popular brands