background image

6

The GoldBug2 requires minimal assembly. To assemble the GoldBug2: 
connect the upper, middle and lower stems, connect the searchcoil 
connector to the back of the control housing and then adjust the angle 
of the searchcoil. Take a look at page 5 and familiarize yourself with the 
parts of the GoldBug2 before proceeding.

1

Unpack your new GoldBug2 carefully. Save the box and inserts 
– they may come in handy for future storage or shipment. 

2

Connect lower, middle and upper stems

 

(see pg. 5 Figure 1). 

3

Adjust the stem length and coil angle so that 
the searchcoil rests flat on the ground about 
6 inches in front of, and slightly to the right 
of, your right foot (for left handers, to the left 
of your left foot). Your arm should be straight 
and relaxed with a lose grip. 

(see Figure 2). 

REMEMBER: THE LONGER THE SHAFT, 

THE MORE YOU WILL HAVE TO BEND 
YOUR ELBOW AND THE SOONER 
YOUR ARM WILL GET TIRED. THE 

G

OLD

B

UG

2

 IS BALANCED FOR 

COMFORTABLE SEARCHING IN A 
TIGHT SEMICIRCLE IN FRONT OF THE 
OPERATOR. 

31

Figure 2.

Adjust the stem 
length and coil 
angle resting the 
searchcoil  flat  on 
the ground and 
about 6 inches in 
front of your right 
foot (left foot for 
left-handers). 

SETTING UP

Length ................................Extended  ............................................53” 
                         Collapsed ............................................40” 

Weight  ...............................Complete ..................................... 2.9 lbs.

1

 

                         Control Housing .......................... 1.0 lbs.

1

 

                         Handle and Coil .......................... 1.9 lbs. 

1

 

Frequency ...........................LF Search ................................. 71.01 kHz 
                         Response .................................... (V.C.O.)

2

 

Operating Modes ................1. All Metal Auto-Tune (NORMAL) 

3

 

                                                 2. All Metal Auto-Tune (BOOST)

                                                 3. Iron Discrimination (DISC) 

3

Mineralization Settings .......1. HIGH (attenuated, fast Auto-Tune) 
                                                 2. NORMAL (fast Auto-Tune) 
                                                 3. LOW (gain boosted, slow Auto-Tune) 

Ground Adjustment  ...........Manual, Digitally controlled high

resolution adjustment 

Control Housing  ................Dust, Moisture Resistant .....................Yes 
Audio Output  .....................Speaker ..................2” Moisture Resistant 
                                                 Headphone Jack .......... 1/4” stereo/mono 

Manual Threshold Tuning  ....... Effective in All Metal, Auto-Tune mode 

Searchcoil  ..........................Type  ..........................Elliptical, Co-Planar
                                                 Sizes available  10” or 6.5” standard, 
                                                  

14” accessory coil 

SPECIFICATIONS

Summary of Contents for Gold Bug-2





































Reviews: