Fisher & Paykel LW015 Service Manual Download | Manualshive

Page: 69 / 92

background image

- 64 -

7.

Unclip the bias spring from the front left suspension
rod. Unclip the neck ring from the top of the outer
bowl.

8.

Remove the fabric softener dispenser, unscrew the
agitator retaining nut and remove the agitator.

9.

The inner bowl may now be lifted clear. (If the inner
bowl is not easy to lift clear, then remove the three
spline retaining screws and remove the driven spline.
Then pull the drive spline off the shaft and lift out the
inner bowl).

If not already removed, the clutch can be
disassembled at this stage by removing
the three screws from the driven spline.

10.

Remove the screw from the drain hose outlet bracket on the rear of the wrapper.

11.

Unclip the harness duct from the right hand rear suspension and remove the suspension assembly
by lifting the corner bracket upwards, and free the suspension assembly from the outer bowl.

12.

Feed the drain hose inside the wrapper. Clip the drain hose fixture over the outer bowl with the
attached hook.

13.

Remove the remaining three suspension rod assemblies.

«
...
67
68
69
70
71
...
»

Summary of Contents for LW015





























































































Reviews:

No comments

Related manuals for LW015

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 34

Brand: GE Pages: 16

Brand: Haier Pages: 16

Brand: Majestic Appliances Pages: 29

Brand: Crosley Pages: 11

Brand: Smeg Pages: 84

Brand: Scheppach Pages: 36

Brand: Ariston Pages: 72

Brand: Allpro Pages: 16

Brand: Bradley Pages: 25

Brand: Neue Pages: 28

Brand: Jetusa Pages: 46

DISHDRAWER DD24SHI9

Brand: Fisher & Paykel Pages: 22

Brand: Miele professional Pages: 56

Brand: IKEA Pages: 16

Brand: Classeq Pages: 21

Brand: BALAY Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands