Fisher & Paykel DE7060G1 Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 12

background image

Property

DE7060G

DE7060P

Rated Power (W)

1770

1770

* Capacity refers to the maximum dry weight of items the

dryer

can dry at any one time.

Some cycles have a lower maximum capacity (see the ‘Drying cycles’ section). Maximum capacity
according to AS/NZS 2442.1:1996.

https://producthelp.fisherpaykel.com/nz/Dry/Dryers/Vented/DE7060G1/User_Guide_DE7060G1/03_Installation_Instructions

Updated: Mon, 05 Oct 2020 18:08:12 GMT

Powered by

12

«
...
10
11
12

Summary of Contents for DE7060G1













Reviews:

No comments

Related manuals for DE7060G1

Brand: GE Pages: 7

Brand: GE Pages: 1

Brand: GE Pages: 3

Brand: GE Pages: 36

Brand: GE Pages: 16

Spacemaker DSXH47

Brand: GE Pages: 48

Profile DPVH880EJ

Brand: GE Pages: 4

Brand: Maytag Pages: 44

Brand: Kalorik Pages: 55

Brand: DeLonghi Pages: 22

Brand: Morphy Richards Pages: 6

Pneudri Maxi MX102c

Brand: Domnick Hunter Pages: 14

Brand: SEVERIN Pages: 56

EconoRed Series

Brand: VASTEX Pages: 20

Brand: Bayou Classic Pages: 16

Brand: Dexter Laundry Pages: 48

Brand: Danby Pages: 44

Brand: Quincy Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands