background image

yourself.

3. Once the grease tray insert is fully visible, unhook its tab in the front and remove.

4. If you need to clean the drip pan too, first ensure you will have a large enough and level surface, such as

a bench- top, for placing it on. You may also want another person to help, as the drip pan is wide and
difficult to balance by one person. Continue pulling the drip pan all the way out, then grab it on either
side (being careful of sharp edges) and remove from its slot. Place on a level surface.

5. To replace, follow these steps in reverse order. Make sure that the grease tray locates securely in place

and the drip pan is pushed all the way back. Take care not to catch your fingers under the handle when
pushing the drip pan in.

Drop-On Griddle Plate (Not Supplied with Unit, Purchased Separately)

Before Using The Griddle for the First Time or to Re-Season

1. Clean the griddle thoroughly with hot soapy water to remove any protective coating.

2. Rinse with a mixture of 4 cups water and 1/4 cup white vinegar. Dry thoroughly.

3. Pour 1 teaspoon vegetable oil into the centre of the griddle (do not use corn oil as it gets sticky). Rub the

oil over the entire surface of the griddle using a heavy cloth.

4. Place the griddle on the centre grill rack, light the burner and turn the control knob to a medium setting.

Turn the heat off when the oil begins to smoke. Allow the griddle to cool.

https://producthelp.fisherpaykel.com/au/Grill/Built-In_Grills/BGB48-BQR/User_Guide_BGB48-BQR/13_Care_and_Maintenance

Updated: Mon, 17 Aug 2020 01:44:59 GMT

Powered by

8

Summary of Contents for BGB48-BQR















Reviews: