background image

FISCHER Mess- und Regeltechnik GmbH

Safety guidelines | 1

BA_EN_DE49_0

5 / 32

• evident damage to the instrument

• failure of the electrical circuits

• longer storage outside the approved temperature range.

• considerable strain due to transport

Repairs may be carried out by the manufacturer only.

A professional single conformity inspection as per DIN EN 61010, section 1,
must be carried out before the instrument can be re-commissioned. This inspec-
tion must be performed at the manufacturer's location. Correct transport and
storage of the instrument are required.

1.5 Unauthorised Modification

Modifications of or other technical alterations to the instrument by the customer
are not permitted. This also applies to replacement parts. Only the manufacturer
is authorised to make any modifications or changes.

1.6 Inadmissible Modes of Operation

The operational safety of this instrument can only be guaranteed if it is used as
intended. The instrument model must be suitable for the medium used in the
system. The limit values given in the technical data may not be exceeded.

The manufacturer is not liable for damage resulting from improper or incorrect
use.

1.7 Safe working practices for maintenance and installation work

The safety instructions given in this operating manual, any nationally applicable
regulations on accident prevention and any of the operating company's internal
work, operating and safety guidelines must be observed.

The operating company is responsible for ensuring that all required mainten-
ance, inspection and installation work is carried out by qualified specialized per-
sonnel.

1.8 Pictogram explanation

 DANGER

Type and source of danger

This indicates a 

direct

 dangerous situation that could lead to death or 

serious

injury 

 (highest danger level).

a) Avoid danger by observing the valid safety regulations.

 WARNING

Type and source of danger

This indicates a 

potentially

 dangerous situation that could lead to death or 

ser-

ious injury 

 (medium danger level).

a) Avoid danger by observing the valid safety regulations.

Summary of Contents for DE49 # 0 series

































Reviews: