background image

 

9  

Long Term Water Treatment and Basic Operation 

Caution: 

 

It is important that a drop cloth be used under the fluid tank whenever the 

tank plug is opened for water treatment.   

The level of resistance is determined by the level indicator located on the front of the tank.  Level 
one indicates lightest resistance, level twenty represents heaviest resistance.  Allow three to four 
seconds after adjusting resistance handle for the correct resistance level to be achieved.     

Long term water treatment: 

Do not use any water treatment other than the tablets supplied with this machine.  

For re-

placement tablets, contact your local First Degree Fitness distributor. 

Water treatment schedules for the E820 will vary according to the fluid tanks exposure to 
sunlight, but expect 8-12 months near a bright, sunlit window and 2 years or more for a darker 
location.  At the point of finding the water slightly cloudy, add a Chlorine tablet.  Remember to 
wait 72 hours following the chlorine tablet before adding the blue dye as the Chlorine tablet is 
extremely concentrated

.   

Important:  

Do not fill past the calibration mark as indicated on the tank level sticker or water 

spillage may occur.  See tank filling/water treatment page for details. 

Resistance: 

Use both hands when either raising or lowering the 
E820control arm.   
 
Removing hands before the crank comes to a com-
plete stop while training can cause injury.  The crank 
is direct drive so as to allow both forward and reverse 
rotation during workouts. 

Warning: 

CAUTION

 

Summary of Contents for Fluid E820





















Reviews: