Firegear Key West KWBH-1 Owners & Installation Manual Download Page 40

Page: 40 / 40

Printed in Canada

Installer: Please complete the following information

Dealer Name & Address: ______________________________________________

___________________________________________________________________

Installer: ___________________________________________________________

Phone #: ___________________________________________________________

Date Installed: ______________________________________________________

Serial No.: __________________________________________________________

fi regear Outdoors® fi replaces are designed with reli-
ability and simplicity in mind. In addition, our inter-
nal Quality Assurance Team carefully inspects each
unit
thoroughly before it leaves our door.

fi regear Outdoors is pleased to extend this Lim-
ited Lifetime Warranty to the original purchaser of a
fi regear Outdoors® Product.

See the inside back cover for details,

Summary of Contents for Key West KWBH-1









































Search results

Summary of Contents for Key West KWBH-1

Reviews:

Firegear Key West KWBH-1, Owners & Installation Manual, Page: 40 / 40

Search results

Summary of Contents for Key West KWBH-1

Reviews: