background image

11

Plug the power cord into a AC 120 Volt outlet (see IMPORTANT SAFETY INFORMATION on Pages 

2 and 3). Make sure the outlet is in good condition and that the plug is not loose. NEVER exceed 
the maximum amperage for the circuit. DO NOT plug other appliances into the same circuit.

This electric fireplace can be operated by the CONTROL PANEL, or by the battery-powered  

REMOTE CONTROL.

Before operating, please review the IMPORTANT SAFETY INFORMATION on Pages 2 and 3, 

and heed all warnings.

 Operation

Read and understand this entire owner’s manual, including all safety information, 
before plugging in or using this product. Failure to do so could result in electric 
shock, fire or serious injury.

Power

Remote Control / Control Panel Operation

Methods of Operation

Control Panel

Remote Control

BUTTON

POWER

TIMER

FUNCTION

ACTION & INDICATION

ON: Enables control panel functions and 
remote control. Turns on flame effect.

OFF: Disables control panel functions and 
remote control. Turns off flame effect.

1. Press once. Indicator lig ht turns on. 
Power turns on. All functions enabled.

2. Press again. Flame effect turns off. Unit 
goes to standby. All functions turn off.

1. Press once. Indicator lig ht turns on. 
Timer is set to 0.5 hours.

2. Press again until desired setting is 
reached. Indicator lig hts show setting.

TIMER button: Controls timer settings to 
turn off fireplace at selected time.
Settings range from 0.5 hours to 8 hours.

FLAME 

BRIGHTNESS

FLAME button: Makes flame effect dimmer 
and brig hter.

NOTE: Flame effect stays on until power 
button is turned off.

1. Press once. Flame brig htness effect gets 
changing.

2. Press again until desired setting 
is reached.

Summary of Contents for SAPPHIRE FB-SPH40

















Reviews: