Fiplex DH140-R User & Installation Manual Download Page 3 | Manualshive

Page: 3 / 45

background image

DH140-R

III

About this manual

This manual describes installation, commissioning, operation and maintenance of the

Fiplex DH140-R Digital Remote Unit

,

and

Fiplex Control Software (FCS)

.

.
The first part of the manual describes the Digital Fiber DAS hardware and the second part describes the software.

Hardware and software mentioned in this manual are subjected to continuous development and improvement. Consequently,
there may be minor discrepancies between the information in the manual and the performance and design of the hardware
and software. Specifications, dimensions and other statements mentioned in this manual are subject to change without notice.

This manual or parts of it may not be reproduced without the written permission of Fiplex Communications Inc.

Infringements will be prosecuted. All rights reserved.

Copyright © Fiplex Communications Inc, Miami, 2017.

«
1
2
3
4
5
...
»

Summary of Contents for DH140-R














































Reviews:

No comments

Related manuals for DH140-R

Brand: D-Link Pages: 2

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

SAFETank Series

Brand: Raidon Pages: 49

Brand: X-Micro Pages: 9

Brand: X-Micro Pages: 19

Brand: D-Link Pages: 213

Brand: Paradyne Pages: 112

Brand: Cambium Networks Pages: 215

OXTOPUS EIA-709

Brand: OCCITALINA Pages: 54

Brand: Cypress Semiconductor Pages: 9

SRCSASBB8I - RAID Controller

Brand: Intel Pages: 36

Brand: Roland Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands