English
- 17 -
Configuring Wired Network Settings in
Advanced Mode
After pressing the
GREEN
button, the “Advanced
mode” will be available. While in Advanced Mode,
press the
RED
button to edit settings. When finished,
press
OK
to save, Press
RETURN
/
BACK
to cancel.
Wireless Connectivity
To Connect to a Wireless Network
IMPORTANT
: “Veezy 200” USB dongle is required to
use wireless network features.
•
To make your modem’s SSID visible, you should
change your SSID settings via the modem’s
software. The TV cannot connect to the networks
with a hidden SSID.
To Connect to a wireless LAN, you should perform
the following steps:
1.
Ensure that Nero Media Home software is
installed to your PC (for DLNA function).
2.
Then connect the wireless adaptor to one of the
USB inputs of the TV.
3.
To configure your wireless settings please refer
to the Network settings section in this manual.
Broadband
ISP
connection
Wireless LAN
adaptor
USB inputs
rear left side
of the TV
•
A Wireless-N router (IEEE 802.11a/b/g/n) with
simultaneous 2.4 and 5 GHz bands is designed
to increase bandwidth. These are optimized for
smoother and faster HD video streaming, file
transfers and wireless gaming.
•
Use a LAN connection for quicker file sharing
between other devices like computers.
•
The frequency and channel differ depending on the area.
•
The transmission speed differs depending on the
distance and number of obstructions between the
transmission products, the configuration of these
products, the radio wave conditions, the line traffic
and the products that you use. The transmission may
also be cut off or may get disconnected depending
on the radio wave conditions, DECT phones or any
other WiFi 11b appliances. The standard values of
the transmission speed are the theoretical maximum
values for the wireless standards. They are not the
actual speeds of data transmission.
•
The location where the transmission is most effective
differs depending on the usage environment.
•
The Wireless LAN adaptor should be connected directly
to the TV’s USB port. USB hubs are not supported. You
can plug your wifi dongle into the supplied dock In
cases where network quality is poor and the wifi
dongle needs to be placed to a location with better
signal quality.
• The Wireless LAN adaptor supports 802.11 a,b,g &
n type modems. It is highly recommended that you
should use the IEEE 802.11n communication protocol
in order to avoid any possible problems while watching
videos.
•
Use the other USB input, if you experience problems
with audio/video performance.
•
You must change your modem’s SSID when there are
any other modems around with the same SSID. You
can encounter connection problems otherwise. Use
a wired connection if you experience problems with a
wireless connection.
Configuring Wireless Device Settings
To enable Wi-Fi features, plug in the Wi-Fi dongle to
one of the USB ports. Open the Network Settings menu
and select
Network Type
as
Wireless Device
to start
connection process.
Press the
YELLOW
button to scan the wireless
networks. A list of available networks will be displayed.
Please select your desired network from the list.
Note:
If the modem supports N mode, you should set
N mode settings.
If the selected network is protected with a password,
please enter the correct key by using the virtual
keyboard. You can use this keyboard via the
navigation
buttons
and the
OK
button on the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established. To
disconnect from a wireless network press
OK
.
You can navigate between menu tabs by pressing left/
right buttons. The help bar on the bottom of the dialog
shows features that you may use. Press the
BLUE
button to check your internet connection speed. Press
the
GREEN
button to switch to advanced mode and
then press the
OK
button to edit settings.
You can check the signal strenght by using the network
settings menu for the wireless device mode.
Other Information
Configuration Status
: Displays Wi-Fi status as
connected or not connected.
IP Address
: Displays the current IP address.
