manualshive.com logo in svg

Fike FIK-5496, Installation & Operation Manual

Share
Download
Fike FIK-5496 Installation & Operation Manual Download Page 6

6

FIK-5496 Manual — 

P/N LS10253-001FK-E:A  03/02/2021

Section 1: Overview

1.1  FIK-5496 Description

The Model FIK-5496 Distributed Power Module provides additional power and notification circuits to the Fike® addressable Fire Alarm 

Control Panels (FACP). The FIK-5496 can power all compatible notification appliances and auxiliary power modules. The FIK-5496 offers 
the following features.
•

The FIK-5496 is capable of performing single or dual interlocking operations for the Pre-action and Deluge Releasing Systems. See 

Section 8.6 of this FACP installation Manual.

•

The FIK-5496 has four output circuits that can be configured as notification or auxiliary power circuits. Outputs are rated 3.0 A (6.0 A 
total for each FIK-5496).

•

The FIK-5496 is optically isolated, providing ground loop isolation and transient protection.

•

The FIK-5496 provides the configuration options that eliminate the need for sychronization modules when you use the AMSECO, 
Faraday, Gentex, System Sensor, or Wheelock synchronization appliances.

1.2  Agency Requirements

TheFIK-5496 has the same requirements as the main control panel. These requirements are listed in the Fike addressable FACP Installation 

Manuals. For additional information, refer to the Fike’s website at www.fike.com.

1.3  How to Contact Fike

If you have a question or encounter a problem not covered in this manual, contact Fike Customer Service listed below: 

Phone:

800-979-FIKE (3453) or 816.229.3405

Website:  

www.fike.com

Address:  

Fike Corporation
704 SW 10th Street 
Blue Springs, MO 64015

Summary of Contents for FIK-5496

















Reviews:

No comments

Brands by name

Popular brands

Load more brands