Fike ECS Series Installation & Operation Manual Download

Page: 42 / 66

ECS Series Manual —

P/N LS10262-001FK-E:A 3/3/2021

Device Installation

Installing the FIK-125W

Wiring Lengths

Class B

Figure 4.34 illustrates how to wire speakers to the control panel using Class B supervision.

Figure 4.34 Class B Speaker Configuration

Class A

Figure 4.35 illustrates how to wire speakers to the control panel using Class A wiring.

Figure 4.35 Class A Speaker Configuration

Number Of Speakers

Total Load

Wire Distance in Feet

@1/2 W

@1 W

Vrms

Watts

18 AWG

16 AWG

14 AWG

12 AWG

25Vrms

3900

6200

9860

15680

25Vrms

10W

2125

3380

5375

8540

25Vrms

15W

1460

2320

3690

5870

25Vrms

20W

1100

1750

2780

4420

25Vrms

26W

760

1200

1920

3050

25Vrms

40W

550

875

1390

2200

100

25Vrms

50W

450

715

1130

1800

150

25Vrms

75W

300

476

753

1200

200

100

25Vrms

100W

225

357

565

900

250

125

25Vrms

125W

180

285

452

720

Table 4.3 Wire Lengths

NOTE:

The above table assumes a uniform distribution of the speakers, and that a max of 20% voltage drop on the last speaker is allowed.

15k

EOL

Supervised

power limited

Supervised

power limited

Summary of Contents for ECS Series



































































Search results

Summary of Contents for ECS Series

Reviews:

Related manuals for ECS Series

Brands by name

Popular brands

Fike ECS Series, Installation & Operation Manual

Search results

Summary of Contents for ECS Series

Reviews:

Related manuals for ECS Series

Brands by name

Popular brands