background image

 

 
 

 

WORK AREA 

 

Keep work area clean, 

free of clutter and well-lit.

 

Cluttered and dark work areas can cause accidents.

 

 

Keep children and bystanders 

away while operating a Tiller. Distractions can cause you to lose control, so 

visitors should remain at a safe distance from the work area.   

 

 

Be alert of your surroundings. 

Using a Tiller in confined work areas may put you dangerously close to cutting 

tools and rotating parts.

 

PERSONAL SAFETY 

 

Stay alert, 

watch what you are doing and use common sense when using a Tiller. Do not use a Tiller while you are 

tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating a Tiller may 

result in serious personal injury. 

 

Dress properly. 

Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves 

away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. 

 

Use safety apparel and equipment. 

Use safety goggles or safety glasses with side shields which comply with 

current national standards, or when needed, a face shield. Use a dust mask if working in dusty work conditions. 

This applies to all persons in the work area. Also use non-skid safety shoes, hardhat, gloves, dust collection 

systems, and hearing protection when appropriate. 

 

TILLER USE AND CARE 

 

Do not modify the Tiller

 

in any way.

 Unauthorized modification may impair the function and/or safety and could 

affect the life of the equipment. There are specific applications for which the Tiller was designed. 

 

Always check for damaged or worn out parts before using the Tiller. 

Broken parts will affect the Tiller 

operation. Replace or repair damaged or worn parts immediately.

 

 

Do not exceed the Tiller

 

load capacity. 

 

Distribute the load evenly.

 Uneven loads may cause the Tiller to tip, resulting in personal injury to the operator or 

others.

 

 

Use the Tiller

 

on flat and level surfaces

 capable of supporting the Tiller and its maximum load. Pulling or 

pushing a load on a slanted or uneven surface can result in loss of control.

 

 

Store idle Tiller. 

When the Tiller is not in use, store it in a secure place out of the reach of children. Inspect it for 

good working condition prior to storage and before re-use. 

 

 

 

 

 

 

3

Summary of Contents for ATV-3665


























Reviews: