Fidelix FX-RP multiDISPLAY
Programming manual
page 37 of 38
Reg# Function
R/W Notes
3061 Play Loud Sound
R/W Play a loud sound. Possible sounds / tunes are:
1: Positive Action
2: Für Elise
3: Turkey March
4: Minuet
5: Solveig’s song
6: Siren 1
7: Siren 2
8: Whistle
9: Tone Scale
10: Positive Beep
11: Negative Beep
12: Disaster Beep
13: Stop Playing
3062 Tamper State
R/W 1023=Tamper detected. Master writes 0 to clear
3063 Boot Loader Startup Register
R/W Used to start bootloader mode, do not change
this value
3064 Non-volatile register
R/W Registers for values that need to be saved upon
power supply interruption.
These values are written to the local memory,
and read from there upon power-up.
Can be written to up to 100 000 times.
3065 Non-volatile register
R/W
3066 Non-volatile register
R/W
3067 Non-volatile register
R/W
3068 Non-volatile register
R/W
Change log
This section describes the changes made forward from firmware version 1.47, and converter version 1.16
released on 10 November 2014. Mentioned numbers are always firmware version number / converter version
number.
1.48 / 1.16:
Calibration timeout defined in register 3048 changed to multiples of 1 second.
1.49 / 1.17:
Converter now looks in the working folder for the presence of the “ModbusMasterSettings.txt” file.
When this is found, master communication is generated. Link to calibration page added.
1.54 / 1.21:
Calibration requires two pushes to be far enough from each other, so erroneous clicks are no longer
validated. #MOMENTARY:x for slave added. “READREG:xx, WRITEREG:yy,” for master added. Added feature
to send fixed values from the display master depending on the internal time schedule status.
1.58 / 1.23:
Added “SINGLEREG” for reading/writing single holding registers from the multiDISPLAY as Modbus
master
1.59 / 1.25:
Register 3053 can now be set from the local display itself also.
1.60 / 1.27:
Added
1.63:
Added free graphical interface possibility for
. Removed necessity to separate
Modbus master and slave projects in different folders. Changed order of loading point values and graphics to
remove delay in graphics update on page load.
1.66 / 1.32:
Ability to read from one Modbus slave and write to another (passing values).
1.71 / 1.34:
Some small bug fixes to previously added functionalities.
1.73 / 1.36:
Register 3017 now contains the day of the week. Added direct link to display settings page. Added
visualisation of the current Modbus address. Added start-up sound disabling possibility. Added ability to write to
µSD card when uploading graphics through Modbus.
1.75 / 1.37:
Increased read timeout from µSD card. Added UINT to Modbus master register value formatting.
1.76 / 1.37:
Small bug fix on the #BYTE values
1.78 / 1.38:
Added math operators. Small bug fix on the summer- to wintertime clock change. Time changes at
04:00 to 03:00 for the change to wintertime, and at 03:00 to 04:00 for the change to summertime.
1.81 / 1.39:
Added possibility to set unused days in time schedules to zero. Signed integers now used for
displaying internal registers. A few minor bug fixes conc/- buttons and constant / momentary values.
1.82 or 2.85 / 1.40:
These two versions are now equivalents for displays from generation 1 and 2.
