Fichtelbahn OpenDCC BiDiB LightControl V1.3, Manual, Page: 2 / 17

Share

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

Page: 2 / 17

Fichtelbahn OpenDCC BiDiB LightControl V1.3 Manual Download Page 2

Table of contents

Introduction ......................................................................................................... 3

1. LightControl: .................................................................................................... 7

2. Construction description of the SMD equipped board: ..................................... 9

Step 1: the power supply ............................................................................................................................ 9

step 2: „function test bootloader“ ........................................................................................................... 10

Step 3: BiDiB-interface ............................................................................................................................. 10

step 4: 16 Power outputs and 8 inputs ..................................................................................................... 11

step 5: 32x LED-outputs: ........................................................................................................................... 11

step 6: 4x servo-outputs: ........................................................................................................................... 12

3. The firmware update ...................................................................................... 13

Approach with the firmware update ............................................................................................. 13

4. Status announcements ................................................................................... 15

5. References ..................................................................................................... 17

Manual to build the SMD pre fitted Hardware

manual-Version V1.4-en

page 2

«
1
2
3
4
...
»

Summary of Contents for OpenDCC BiDiB LightControl V1.3


















Reviews:

No comments