manualshive.com logo in svg

Fichtelbahn OpenDCC BiDiB LightControl V1.3, Manual, Page: 17 / 17

Share
Download
Fichtelbahn OpenDCC BiDiB LightControl V1.3 Manual Download Page 17

 

 

 

5. References 

 

The continuing instructions "

introduction and use

" deal with the following main 

topics: 

 

- Introduction 

- Functionality of the macros 

- Configutariontool "BiDiB-Wizard Tool" 

- Debuginterface 

 

 

       - Application in connection with railroad software 

                                 - Firmware update 

 

 

 

I am very grateful for improvement suggestions and tips to mistakes.

 

 

 

On the construction manual or any software there is no liability for any damages or functional guarantee. 

 I do not guarantee for damages which cause the user or third parties by the use of the software or hardware 

or suffer. In no case I guarantee for escaped turnover or profit or other property damages by the use or by 

the use of these programmes or instructions can originate. 

 

With further inquiries our Support forum is available to you with pleasure! 

(www.opendcc.de/forum)

 

 

 

 

contact: 

 

fichtelbahn.de 

Christoph Schörner 

Ahornstraße 7 

D-91245 Simmelsdorf 

 

[email protected] 

 

 

 

 

© 2014 Fichtelbahn 

 

All rights, in particular the right of her 

Duplication and spreading as well as 

of the translation reserve. 

Duplications and reproductions 

in any form need her 

written approval by Fichtelbahn. 

Technical changes reserve. 

 

Manual to build the SMD pre fitted Hardware   

 

  

 

 

manual-Version V1.4-en 

 

 

page 17 

Summary of Contents for OpenDCC BiDiB LightControl V1.3


















Reviews:

No comments