manualshive.com logo in svg

Fichtelbahn OpenDCC BiDiB LightControl V1.3, Manual, Page: 13 / 17

Share
Download
Fichtelbahn OpenDCC BiDiB LightControl V1.3 Manual Download Page 13

 

 

 

3. The firmware update 

 

With the SMD equipped LightControl we have this already done for you! The LightControl is 

completely ready for use with the actual Bootloader, the actual firmware and the printed 

serialnumber. 

 

The chapter „firmware update“ describes only the steps for the case of an update if a new firmware 

is available for the LightControl! 

 

In other cases (first introduction if still no firmware  was uploaded)please read the programming 

steps in the construction instructions of the soldering kit. 

 

3.1  Approach with the firmware update 

 

 The 

LightControl

 can become beside the 

Programmer also directly flashed with 

the BiDiB-

Wizard tool

. This function should be also used at 

a firmware update

.  

 

The advantage is: 

The LightControl can be updated in the built-in 

state with the tool, you also speaks of a distant 

servicing. 

In the knot list of the BiDiB-Wizard tool you find 

your LightControl and all other BiDiB 

components, for configuration or for a firmware 

update. 

 

Download the actual firmware for the 

LightControl from our web page and ectract the 

ZIP file on your PC

. 

 

Tip: 

Use with an update only the file with the name: 

lightcontrol_update…000.hex 

 

With this all macro and settings remain you 

have configured on the LightControl preserved 

and are not overwritten by Default values 

.  

 

 

You must transfer only this file to the LightControl with the BiDiB-Wizard tool. 

 

Both other files are the firmware files for the first introduction. By use your stored settings with the Default 

values are overwritten (default settings). 

 

 

 

Manual to build the SMD pre fitted Hardware   

 

  

 

 

manual-Version V1.4-en 

 

 

page 13 

Summary of Contents for OpenDCC BiDiB LightControl V1.3


















Reviews:

No comments