Fibocom NL952-NA-00 Hardware User Manual Download

Page: 33 / 57

FIBOCOM_NL952-NA_Hardware_User_Manual

Page 33 of 57



Two pairs of differential signal lines should be parallel and have the equal length, the right angle

routing should be avoided.



The two pairs differential signal lines should be routed on the layer that is adjacent to the ground layer,

and wrapped with GND vertically and horizontally.

3.5 USIM Interface

The NL952 module support dual SIM card single standby, has dual built-in USIM card interface, which

supports 1.8V and 3V SIM cards.

USIM1 Pins

The USIM1 pins description as shown in the following table:

Pin

Pin Name

I/O

Reset Value Description

Level

UIM_PWR

PO -

USIM power supply

1.8V/3V

UIM_RESET

USIM reset

1.8V/3V

UIM_CLK

USIM clock

1.8V/3V

UIM_DATA

I/O

USIM data, internal pull up(4.7K

)

1.8V/3V

SIM_DETECT

USIM card detect, internal 390K pull-

up.

Active high, and high level indicates

SIM card is inserted; and low level

indicates SIM card is detached.

1.8V

USIM2 Pins

The USIM2 pins description as shown in the following table:

Pin

Pin Name

I/O

Reset Value Description

Level

UIM2_PWR

PO -

USIM2 power supply

1.8V/3V

UIM2_RESET

USIM2 reset

1.8V/3V

UIM2_CLK

USIM2 clock

1.8V/3V

UIM2_DATA

I/O

USIM2 data, internal pull up(4.7K

) 1.8V/3V

SIM2_DETECT

USIM2 card detect, internal 390K

pull-up.

Active high, and high level indicates

SIM card is inserted; and low level

indicates SIM card is detached.

1.8V

Summary of Contents for NL952-NA-00

























































Search results

Summary of Contents for NL952-NA-00

Reviews:

Related manuals for NL952-NA-00

Brands by name

Popular brands

Fibocom NL952-NA-00, Hardware User Manual

Search results

Summary of Contents for NL952-NA-00

Reviews:

Related manuals for NL952-NA-00

Brands by name

Popular brands