Fibocom NL952-NA-00 Hardware User Manual Download Page 47 | Manualshive

Page: 47 / 57

background image

Reproduction forbidden without Fibocom Wireless Inc. written authorization - All Rights Reserved.

FIBOCOM_NL952-NA_Hardware_User_Manual

Page 47 of 57

Description

Condition

Test Result

Max

Typical

Current

Fixing

110mA@-130dBm

TBD

Tracking

110mA@-130dBm

TBD

Sleep

3.5mA@-130dBm

TBD

TTFF

Cold start

45s@-130dBm

TBD

Hot Start

3s@-130dBm

TBD

Sensitivity

Tracking

-156dBm

TBD

Acquisition

-144dBm

TBD

Note:

GNSS current is tested with RF disabled at 25

℃

temperature.

4.6 Antenna Design

The NL952module provides main and diversity antenna interfaces, and the antenna design requirements

as shown in the following table:

NL952 module Main antenna requirements

Frequency range

The most proper antenna to adapt the frequencies should be used.

Bandwidth(WCDMA)

WCDMA band 2(1900) : 140 MHz
WCDMA band 4(2100) : 445 MHz
WCDMA band 5(850) : 70 MHz

Bandwidth(LTE)

LTE band 2(1900):      140 MHz
LTE Band 4(2100):      445 MHz
LTE band 5(850):        70 MHz
LTE band 7(2600):      190 MHz
LTE Band 12(700):        47 MHz
LTE band 13(770) :      41 MHz
LTE band 14(750) :      40 MHz
LTE band 17(700):      42 MHz
LTE band 25(1900):      145 MHz
LTE band 26(850):      80 MHz
LTE band 29(700):      11 MHz
LTE band 30(2300):      10 MHz
LTE band 41(2500):      110 MHz
LTE band 46(5

500

): 775 MHz

LTE band 48(3600): 150 MHz
LTE band 66(2100): 490 MHz

«
...
45
46
47
48
49
...
»

Summary of Contents for NL952-NA-00


























































Reviews:

No comments

Related manuals for NL952-NA-00

Brand: Vanguard Pages: 4

Brand: Compaq Pages: 112

Brand: Teletronics International Pages: 57

Brand: Supero Pages: 16

Brand: CNC4PC Pages: 11

Brand: Rajant Corporation Pages: 40

Brand: Abit Pages: 22

Suzie-Q 541.35.520

Brand: Hafele Pages: 12

Slideaway CL1008

Brand: ATEN Pages: 77

SFD-2 MkIII Jumper

Brand: Anthem Audio Pages: 2

Brand: UMAX Technologies Pages: 27

Brand: Flexwatch Pages: 13

Brand: Matrix Switch Corporation Pages: 48

Brand: Commell Pages: 18

Hotwire 5620 RTU

Brand: Paradyne Pages: 20

SmartRack SR42UBEXPKD

Brand: Tripp Lite Pages: 8

Brand: ICP Pages: 111

Brand: SilverStone Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands