Fibocom FM350-GL Hardware Manual Download Page 7

Page: 7 / 59

FM350-GL Hardware Guide

Page 7 of 59

1 Foreword

1.1

Introduction

The document describes the electrical characteristics, RF performance, dimensions and application

environment, etc. of

FM350-GL (hereinafter referred to as FM350). With the assistance of the document

and other instructions, the developers can quickly understand the hardware functions of FM350 modules

and develop products.

1.2

Reference Standard

The design of the product complies with the following standards:

⚫

3GPP TS 38.300 V15.5.0 : 3rd Generation Partnership Project; Technical Specification Group Radio

Access Network; NR; NR and NG-RAN Overall Description; Stage 2

⚫

3GPP TS 38.521-1 V15.2.0 : User Equipment (UE) conformance specification; Radio transmission

and reception; Part 1: Range 1 Standalone

⚫

3GPP TS 38.521-3 V15.2.0 :User Equipment (UE) conformance specification; Radio transmission

and reception; Part 3: Range 1 and Range 2 Interworking operation with other radios

⚫

3GPP TS 34.121-1 V8.11.0: User Equipment (UE) conformance specification; Radio transmission

and reception (FDD);Part 1: Conformance specification

⚫

3GPP TS 34.122 V14.0.0: Technical Specification Group Radio Access Network; Radio transmission

and reception (TDD)

⚫

3GPP TS 36.521-1 V14.0.0: User Equipment (UE) conformance specification; Radio transmission

and reception; Part 1: Conformance testing

⚫

3GPP TS 21.111 V10.0.0: USIM and IC card requirements

⚫

3GPP TS 51.011 V4.15.0: Specification of the Subscriber Identity Module -Mobile Equipment (SIM-

ME) interface

⚫

3GPP TS 31.102 V10.11.0: Characteristics of the Universal Subscriber Identity Module (USIM)

application

⚫

3GPP TS 31.11 V10.16.0: Universal Subscriber Identity Module (USIM) Application Toolkit(USAT)

⚫

3GPP TS 36.124 V10.3.0: Electro Magnetic Compatibility (EMC) requirements for mobile terminals

and ancillary equipment

⚫

3GPP TS 27.007 V10.0.8: AT command set for User Equipment (UE)

⚫

3GPP TS 27.005 V10.0.1: Use of Data Terminal Equipment - Data Circuit terminating Equipment

(DTE - DCE) interface for Short Message Service (SMS) and Cell Broadcast Service (CBS)

⚫

PCI Express M.2 Specification Rev1.2

Summary of Contents for FM350-GL

























































Search results

Summary of Contents for FM350-GL

Reviews:

Brands by name

Popular brands

Fibocom FM350-GL, Hardware Manual

Search results

Summary of Contents for FM350-GL

Reviews:

Brands by name

Popular brands