Fiberplex SFP-BHDVXC-0000-L, User Manual

Page: 20 / 24

Specifications
ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings Symbol Min Typ Max Unit
Exceeding any of these ratings may permanently damage the module. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Absolute Maximum Voltage Range V
CC_MAX
0 3.3 3.6 VDC
Environmental
Storage Temperature T
s
‐40 ‐ +85 °C
Operating Temperature T
C_MAX
‐40 ‐ +80 °C
Operating Relative Humidity
(non condensing)
5 ‐ 95 %
ESD Rating ‐ ‐ 1 kV HBM
Recommended Operating Conditions Symbol Min Typ Max Unit
Unless otherwise specified, all specifications are valid under these conditions: VCC = 3.3V ±5%, TC = ‐40°C to +80°C.
Specifications are guaranteed by design and characterization.
Recommended
Operating Conditions
Supply Voltage V
CC
3.13 3.3 3.465 VDC
Operating Case Temperature T
C
‐40 ‐ +80 °C
Serial Data Rate SD (SMPTE 259M, C) BR
SD
‐ 270 ‐ Mbps
Serial Data Rate HD (SMPTE 292M) BR
HD
‐ 1483, 1485 ‐ Mbps
Serial Data Rate 3G SMPTE (424M) BR
3G
‐ 2967, 2970 ‐ Mbps
DC characteristics
Power Supply Current 1
(RX1 <140m)
I
CC
‐ 348 402 mA
Power Supply Current 1
(RX1 >140m)
I
CC
‐ 368 427 mA
Power Supply Current
2
(Save Mode)
I
CC (Save Mode)
‐ 288 331 mA
Total Power Consumption 1
(RX1 >140m)
P
D
‐ 1216 1410 mW
1. All power consumption characterised at 25°C
2. Save Mode is activated when Autosleep register is set HIGH and no input is detected on RX Channel
Digital I/O Characteristics ‐ Logic Symbol Min Typ Max Unit
TX_DIS (Input)
Input Voltage Low V
IL
‐ ‐ 0.8 V
Input Voltage High V
IH
2.0 ‐ ‐ V
Rpull‐up R
PU
4.7 ‐ 10 kΩ
LOS (Output)
Output Voltage Low (I
OL
=10μA)
V
OL
‐ ‐ 0.1 V
Output Voltage Low (I
OL
=8.5μA) ‐ ‐ 0.6 V
MOD_DEF2 (Output)
Output Voltage Low (I
OL
=10μA)
V
OL
‐ ‐ 0.1 V
Output Voltage Low (I
OL
=8.5μA) ‐ ‐ 0.6 V
MOD_DEF1 &
MOD_DEF2 (Input)
1
Input Voltage Low V
IL
‐ ‐ 0.8 V
Input Voltage High V
IH
2.0 ‐ ‐ V
1. MOD_DEF1 (SCL) & MOD_DEF2 (SDA) must be pulled up to V
CC
with a 4.7k‐10kΩ on the host board
Digital I/O Characteristics ‐ Data Symbol Min Typ Max Unit
RD± (Output) 1
Single‐ended Voltage Swing 3 V
O P‐P
310 375 440 mVP‐P
Differential Voltage Swing 3 V
ODIFF P‐P
620 750 880 mVP‐P
Differential Impedance 3 Z
ODIFF
90 100 110 Ω
Rise Time, Fall Time
3
(20% ‐ 80%) t
r
, t
f
‐ 90 130 ps
Serial Data Output Jitter 4, 5, 6
t
JIT‐SD
‐ 0.01 0.03 UI
t
JIT‐HD
‐ 0.03 0.04 UI
t
JIT‐3G
‐ 0.06 0.08 UI
Reclocker Loop Bandwidth
(270 Mbps, <0.1dB Peaking)
BW
LOOP‐SD
‐ 275 ‐ KHz
(1485 Mbps, <0.1dB Peaking)
BW
LOOP‐HD
‐ 1.5 ‐ MHz
(2970 Mbps, <0.1dB Peaking)
BW
LOOP‐3G
‐ 2.75 ‐ MHz
Reclocker Acquisition Time
7
T
ACQ
‐ ‐ 15 ms
TD± (Input) 2
Differential Voltage Swing V
IDIFF
200 ‐ 1600 mVP‐P
Differential Impedance Z
IN
90 100 110 Ω
Input Rise Time / Fall Time (270 Mbps) t
r‐
, t
f‐
‐ ‐ 1500 ps
(1485 Mbps) t
r
, t
f
‐ ‐ 270 ps
(2970 Mbps) t
r
, t
f
‐ ‐ 135 ps
Serial Input Jitter Tolerance
(
A1
‐Timing Jitter – RP184‐1996)
(
A2
‐ Alignment Jitter ‐ RP184‐1996)
TOL
JIT‐SD‐A1
>6 ‐ ‐ UI
P‐P
TOL
JIT‐SD‐A2
>0.6 ‐ ‐ UI
P‐P
TOL
JIT‐HD‐A1
>6 ‐ ‐ UI
P‐P
TOL
JIT‐HD‐A2
>0.6 ‐ ‐ UI
P‐P
TOL
JIT‐3G‐A1
>6 ‐ ‐ UI
P‐P
TOL
JIT‐3G‐A2
>0.6 ‐ ‐ UI
P‐P
Reclocker Loop Bandwidth
(270 Mbps, <0.1dB Peaking)
BW
LOOP‐SD
‐ 275 ‐ KHz
(1485 Mbps, <0.1dB Peaking)
BW
LOOP‐HD
‐ 1.5 ‐ MHz
(2970 Mbps, <0.1dB Peaking)
BW
LOOP‐3G
‐ 2.75 ‐ MHz
Reclocker Acquisition Time 7 T
ACQ
‐ ‐ 15 ms