background image

21

REGULATIOnS

Note

Changes and modifications not expressly approved by the manufactu-

rer or registrant of this equipment can void your authority to operate 

this equipment under Federal Communications Commission’s rules.

DGT Warning Statement
Article 12 

Without permission, any company, firm or user shall not alter the fre-

quency,  increase the power, or change the characteristics and func-

tions of the original design of the certified lower power frequency elec-

tric machinery. 

Article 14 

The application of low power frequency electric machineries shall not 

affect the navigation safety nor interfere a legal communication, if an 

interference is found, the service will be suspended until improvement 

is made and the interference no longer exists. 

第十二條

經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用

者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 

第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現

有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。 

前項合法通信,指依電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性

電機設備之干擾。

Declaration of conformity

hereby, Fibar Group S.A. declares that FIBARO KeyFob is 

in compliance with the essential requirements and other 

relevant provisions of Directive 1999/5/EC.

Summary of Contents for KEYFOB FGKF-601






















Reviews: