background image

Go to fetco.com for the latest versions of all information         Page 18               

  

P183   March 2019

 

Figure 4 – CBS-52H15 & CBS-52H20 Tank Assembly

 

 

REF 

QTY 

PART NO 

DESCRIPTION 

1114.00133.00  

WELDMENT TANK, CBS-52H 

1084.00022.00  

NUT, 3/4-16 HEX JAM, 18-8SS 

1031.00029.00  

BUSHING, 3/4-16 X 1/4 NPSM, HEX HEAD 

1031.00026.00  

FITTING, HEX NIPPLE, 3/8 NPT X 1/4 NPT 

1034.00002.00  

VALVE, BALL 3/8 FPT X 3/8 FPT 

1031.00025.00  

FITTING, BARB, 1/2 HOSE ID X 3/8 NPT 

1-3 

1003.00005.00  

BRACKET, ONE SHOT THERMOSTAT 

1-3 

1053.00004.00  

THERMOSTAT, SINGLE SHOT, 25A 

1083.00009.00  

WASHER, #6 SCREW , INTL TOOTH LOCKWASHER 

10 

1084.00010.00  

NUT, HEX, #6-32, UNDERSIZED, ZINC PLATED 

11 

1013.00030.00  

LOCKNUT, 7/16, DISPENSE FITTING 

12 

1013.00029.00  

FITTING, DISPENSE, 7/16" DIA. 

13 

1024.00024.00  

SEAL, DISPENSE TUBE, 7/16"DIA 

14 

1012.00003.00  

LOCKNUT, SEAL, 7/16" DIA KEEPER 

15 

1031.00033.00  

LOCKNUT, 3/8"-18 NPT THREAD 

16 

1031.00024.00  

FITTING, COMP., MALE CONN., 3/8 TUBE X 3/8 

17 

1031.00020.00  

LOCKNUT 1/8" STRAIGHT PIPE THREAD 

18 

1083.00014.00  

WASHER, .812"OD X 0.412"ID FLAT 

19 

1031.00032.00  

FITTING, BARB, ELBOW 90°, 1/4 HOSE ID X 1/8 NPT 

20 

1023.00003.00  

LOCKNUT, MODIFIED THREAD, 1/4-18 NPT 

21 

1083.00006.00  

WASHER, .875" OD X 0.562" ID FLAT 

22 

1025.00001.00  

FITTING, COMPRESSION MALE CONNECTOR 

23 

1102.00291.00  

ASSEMBLY DIGITAL TEMP. PROBE, 14.0"LG. 

24 

1112.00333.00  

WELDMENT, TANK FILL TUBE 

25 

1024.00007.00  

O-RING, DASH #344, TANK COVER 

26 

1102.00007.00  

TANK COVER ASSEMBLY 

27 

1-3 

1107.00005.00  

HEATER ASSEMBLY, IMMERSION 3000W, 240VAC 

27 

1-3 

1107.00010.00  

HEATER ASSEMBLY, IMMERSION 4000W/240VAC 

28 

1-3 

1003.00140.00  

ALUMINUM BRACKET FOR SSR 

29 

1-3 

1052.00033.00  

RELAY, SOLID STATE, 50A/480VAC, W/BUILD IN VARISTOR 

30 

1081.00042.00  

STANDOFF, 1/4" HEX 

31 

1102.00292.00  

ASSEMBLY, LEVEL PROBE, 1.75" LG. X 0.25" DIA 

32 

1044.00004.00  

LABEL, DANGER, HIGH VOLTAGE 

For tank assembly and wiring diagram part numbers, call Tech Support at 800-338-2699.  Provide the brewer serial number when callin

 

 

Drawing No. 104075

TANK ASSEMBLY, CBS-52H

Summary of Contents for CBS-5000H Series























Reviews: