background image

DSMI-B

Festo DSMI-B 2017-12d English

7

Unauthorised product modification is not permitted.

Note the warnings and instructions on the product and in the relevant 
operating instructions.

Take the tolerance of the tightening torques into account. Without special
specification, the tolerance is ±20 %.

5

Installation

Mechanical installation

For electronically closed-loop control of the DSMI in combination with a position­
ing controller:

Note

Special installation specifications apply to the electronically controlled 
operation.

 To install the mechanical system, please observe the instructions in the 

descriptions of the positioning controller.

The following applies to all applications:

Handle the DSMI with care so that the drive shaft is not damaged. This applies
in particular to the following:

Check whether it is necessary to drill
additional holes in the mounting flange
of the DSMI.

The grey areas (G) in the drawing show
where additional holes can be drilled on
the DSMI (e.g. to mount centring pins).

Position the DSMI so that you can easily reach the operating parts.

Fasten the DSMI with at least 2 screws.

Fig. 2

(G)

Summary of Contents for DSMI-***-B Series

























Reviews: